Sony XAV-601BT User Manual Page 2
- Page / 2
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Precautions
Choose the installation location carefully so that the
unit will not interfere with normal driving operations.
Avoid installing the unit in areas subject to dust, dirt,
excessive vibration, or high temperature, such as in
direct sunlight or near heater ducts.
Use only the supplied mounting hardware for a safe and
secure installation.
To attach/detach the front panel smoothly and
especially to drive safely, a certain distance between the
front panel and the shift lever is necessary. The
necessary distance differs, depending on the shift lever
position of your car. Before installing the unit, choose
the installation location carefully so that you can drive
safely.
Mounting angle adjustment
Adjust the mounting angle to less than 45°.
Connecting the parking brake
lead
Be sure to connect the parking brake lead (light green) of
the power supply connection cable to the parking
brake switch cord. The mounting position of the parking
brake switch cord depends on your car. Consult your car
dealer or your nearest Sony dealer for further details.
Installing the microphone
To capture your voice during handsfree calling, you need
to install the microphone .
Cautions
Keep the microphone away from extremely high
temperatures and humidity.
It is extremely dangerous if the cord becomes wound
around the steering column or gearstick. Be sure to
keep it and other parts from obstructing your driving.
If airbags or any other shock-absorbing equipment is in
your car, contact the store where you purchased this
unit, or the car dealer, before installation.
-A Installing on the sun visor
1 Install the microphone
a
on the clip
b
.
2 Install the clip
b
on the sun visor.
3 Install clips (not supplied) and adjust the length
and position of the cord so that it does not
obstruct your driving.
-B Installing on the dashboard
1 Install the microphone
a
on the clip
b
, then
place the cord along the groove of the clip
b
.
2 Attach the clip
b
to the dashboard with the
double-sided tape
c
.
3 Install a clip (not supplied) and adjust the length
and position of the cord so that it does not
obstruct your driving.
Notes
Before attaching the double-sided tape
c
, clean the surface of the
dashboard with a dry cloth.
Adjust the microphone angle to the proper position.
The microphone
a
can be installed without using the clip
b
.
In this case, directly attach the microphone to the dashboard with the
double-sided tape
c
. Keep the unused clip
b
for future use.
How to detach and attach the
front panel
Before installing the unit, detach the front panel.
-A To detach
Before detaching the front panel, be sure to press and
hold . Press
, and then hold the left
side of the front panel and pull it open to the right.
Tip
If you also lift the left side of the front panel slightly , the front panel
comes out easily.
-B To attach
Place the recesses of the front panel onto the pegs
on the unit, then lightly push the left side in.
Removing the bracket
Before installing the unit, remove the bracket
from the unit.
1 Insert both release keys together between
the unit and the bracket until they click.
2 Pull down the bracket , then pull up the unit
to separate them.
Foot brake type Hand brake type
Parking brake switch cord
Parking brake switch cord
A A
B B
2
1
2
1
b
a
c
b
a
Mounting the unit
-A Mounting the unit with the supplied
bracket
1 Position the supplied bracket inside the
dashboard.
2 Bend the claws outward for a tight fit.
3 Mount the unit onto the supplied bracket .
-B Mounting the unit in a Japanese car
You may be able to install this unit in some makes of
Japanese cars without the supplied bracket. If you cannot,
consult your Sony dealer.
When mounting this unit to the preinstalled brackets of
your car, use the supplied screws in the appropriate
screw holes, based on your car: T for TOYOTA, M for
MITSUBISHI and N for NISSAN.
Notes
To avoid a malfunction, install only with the supplied screws .
Do not apply excessive force to the buttons of the unit.
Do not press on the LCD.
Before mounting, make sure there is nothing on the top of the unit.
Warning if your car’s ignition
has no ACC position
Be sure to set the Auto Off function. For details, refer to
the supplied “Operating Instructions.”
The unit will shut off completely and automatically in the
set time when no source is selected, which prevents
battery drainage.
If you do not set the Auto Off function, press and hold
until the display disappears each time
you turn the ignition off.
Reset button
When the installation and connections are completed, be
sure to press the reset button, which is located behind the
front panel, with a ballpoint pen, etc.
Dashboard
Claws
2
3
1
A B
Larger than 182 mm (7
1
/4 in)
Larger than 111 mm (4
3
/8 in)
To the dashboard/center console
Bracket
Parts supplied with your car
Size:
5 × max. 8 mm
(
7
/32 × max.
5
/16 in)
Size:
5 × max. 8 mm
(
7
/32 × max.
5
/16 in)
Bracket
b
a
Clips (not supplied)
c
b
a
Clip (not supplied)
Face the hook inwards.
1
2
Related products and manuals for Motorcycle Accessories Sony XAV-601BT
(11 pages)
(4 pages)
(2 pages)© 2020, manymanuals.com. All rights reserved. | 2.016 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals