Sony MEX-BT2600 User Manual
Browse online or download User Manual for Motorcycle Accessories Sony MEX-BT2600. Sony MEX-BT2600 Installation Guide
- Page / 2
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
SONY MEX-BT2600 (GB,AR) 3-278-366-61 (1)SONY MEX-BT2600 (GB,AR) 3-278-366-61 (1)
3
L
R
2
4
6
5
1
REAR/SUB FRONT
AUDIO OUT
BU
S
IN
BUS AUDIO IN
BUS
CONTROL IN
REMOTE
IN
REAR
/
SUB
AUDIO OUT
*
2
FRONT
AUDIO OUT
3-278-366-61 (1)
Cautions
Be sure to install this unit in the dashboard of the car
as the rear side of the unit becomes hot during use.
• This unit is designed for negative ground (earth) 12 V
DC operation only.
• Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).
• Before making connections, turn the car ignition off to
avoid short circuits.
• Connect the yellow and red power input leads only
after all other leads have been connected.
• Run all ground (earth) leads to a common
ground (earth) point.
• Be sure to insulate any loose unconnected leads with
electrical tape for safety.
• Do not cover the ventilation slots or heat sinks of the
unit.
Notes on the power supply lead (yellow)
• When connecting this unit in combination with other
stereo components, the connected car circuit’s rating
must be higher than the sum of each component’s fuse.
• When no car circuits are rated high enough, connect
the unit directly to the battery.
Parts Iist
• The numbers in the list are keyed to those in the
instructions.
• The bracket and the protection collar are
attached to the unit before shipping. Before mounting
the unit, use the release keys to remove the bracket
and the protection collar from the unit. For
details, see “Removing the protection collar and the
bracket ()” on the reverse side of the sheet.
• Keep the release keys for future use as they
are also necessary if you remove the unit from
your car.
Caution
Handle the bracket carefully to avoid injuring your
fingers.
Catch
Note
Before installing, make sure that the catches on both sides of
the bracket are bent inwards 2 mm. If the catches are straight
or bent outwards, the unit will not be installed securely and may
spring out.
Connection example
Notes (-
A
)
• Be sure to connect the ground (earth) lead before connecting
the amplifier.
• The alarm will only sound if the built-in amplifier is used.
Installation/Connections
Connection diagram
To a metal surface of the car
First connect the black ground (earth) lead, then connect the
yellow and red power supply leads.
To the power antenna (aerial) control lead or
power supply lead of antenna (aerial) booster
amplifier
Notes
• It is not necessary to connect this lead if there is no power
antenna (aerial) or antenna (aerial) booster, or with a
manually-operated telescopic antenna (aerial).
• When your car has a built-in FM/AM antenna (aerial) in
the rear/side glass, see “Notes on the control and power
supply leads.”
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting any other
system may damage the unit.
To the interface cable of a car telephone
To the +12 V power terminal which is
energized in the accessory position of the
ignition key switch
Notes
• If there is no accessory position, connect to the +12 V
power (battery) terminal which is energized at all times.
Be sure to connect the black ground (earth) lead to a
metal surface of the car first.
• When your car has a built-in FM/AM antenna (aerial) in
the rear/side glass, see “Notes on the control and power
supply leads.”
To the +12 V power terminal which is
energized at all times
Be sure to connect the black ground (earth) lead to a metal
surface of the car first.
Notes on the control and power supply leads
• The power antenna (aerial) control lead (blue) supplies +12 V
DC when you turn on the tuner.
• When your car has built-in FM/AM antenna (aerial) in the rear/
side glass, connect the power antenna (aerial) control lead
(blue) or the accessory power input lead (red) to the power
terminal of the existing antenna (aerial) booster. For details,
consult your dealer.
• A power antenna (aerial) without a relay box cannot be used
with this unit.
Memory hold connection
When the yellow power input lead is connected, power will
always be supplied to the memory circuit even when the ignition
switch is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with
adequate power handling capacities to avoid its damage.
• Do not connect the speaker terminals to the car chassis, or
connect the terminals of the right speakers with those of the
left speaker.
• Do not connect the ground (earth) lead of this unit to the
negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active speakers
(with built-in amplifiers) to the speaker terminals may damage
the unit.
• To avoid a malfunction, do not use the built-in speaker leads
installed in your car if the unit shares a common negative (–)
lead for the right and left speakers.
• Do not connect the unit’s speaker leads to each other.
Note on connection
If speaker and amplifier are not connected correctly, “FAILURE”
appears in the display. In this case, make sure the speaker and
amplifier are connected correctly.
REAR AUDIO OUT
FRONT AUDIO OUT
SUB AUDIO OUT
FRONT AUDIO OUT
A
B
Equipment used in illustrations (not supplied)
from car antenna (aerial)
Rear speaker
Front speaker
Active subwoofer
Rotary commander RM-X4S
Power amplifier
× 2
× 4
CD/MD changer
BUS AUDIO IN
BUS CONTROL IN
AMP REM
Max. supply current 0.3 A
Fuse (10 A)
Blue/white striped
White
Green
Purple
White/black striped
Grey/black striped
Green/black striped
Grey
Left
Right
Left
Right
ANT REM
Max. supply current 0.1 A
Purple/black striped
*
1
Supplied with the CD/MD changer
*
1
ATT
MEX-BT2600
*
3
*
1
RCA pin cord (not supplied)
*
2
AUDIO OUT can be switched SUB or
REAR. For details, see the supplied
Operating Instructions.
*
3
Insert with the cord upwards.
Bluetooth™
Audio System
©
2008 Sony Corporation Printed in Thailand
Black
Blue
Red
Yellow
Light blue
1
2
Summary of Contents
Page 1 - Audio System
SONY MEX-BT2600 (GB,AR) 3-278-366-61 (1)SONY MEX-BT2600 (GB,AR) 3-278-366-61 (1)3LR24651REAR/SUB FRONTAUDIO OUTBUSINBUS AUDIO INBUSCONTROL INREMOTEI
Page 2 - 2 Remove the bracket
SONY MEX-BT2600 (GB,AR) 3-278-366-61 (1)SONY MEX-BT2600 (GB,AR) 3-278-366-61 (1)12 3182 mm53 mmDashboardA TOYOTAto dashboard/centre consoleBracke
Related products and manuals for Motorcycle Accessories Sony MEX-BT2600
(2 pages)
(2 pages)
(2 pages)
(4 pages)© 2020, manymanuals.com. All rights reserved. | 2.006 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals