Sony XAV-601BT User Manual
Browse online or download User Manual for Motorcycle Accessories Sony XAV-601BT. Sony XAV-601BT Installation guide
- Page / 2
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
4-419-668-54(1)
Installation/Connections
AV Center
XAV-601BT
AUX1 IN
AUX2 AUDIO
IN
REVERSE IN
Z
x
Z L
/
R
*
6
SUB OUT
AUX1 AUDIO
IN
FRONT
AUDIO OUT
REAR
AUDIO OUT
MIC IN
*
3
REMOTE IN
*
7
AUX2 IN
CAMERA
REAR OUT
EXT
AUX IN
(
VIDEO
)
AUX AUDIO
IN
CAMERA
AUX1 IN
(
VIDEO
)
Connection example
Notes (-
A
)
Be sure to connect the ground (earth) lead before connecting the amplifier.
The alarm will only sound if the built-in amplifier is used.
Notes (-
B
)
You cannot use multiple auxiliary devices simultaneously, even if they
are connected to different terminals.
To connect an iPod via RC-202IPV, make sure to connect the video
output plug to AUX1 IN.
Connection diagram
To a common ground (earth) point
First connect the black ground (earth) lead, then connect the yellow
and red power supply leads.
To the power antenna (aerial) control lead or the
power supply lead of the antenna (aerial) booster
Notes
It is not necessary to connect this lead if there is no power antenna
(aerial) or antenna (aerial) booster, or with a manually-operated
telescopic antenna (aerial).
If your car has a built-in FM/AM antenna (aerial) in the rear/side
glass, see “Notes on the control and power supply leads.”
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting any other system
may damage the unit.
To a car’s illumination signal
Be sure to first connect the black ground (earth) lead to a common
ground (earth) point.
To the +12 V power terminal which is energized
when the ignition switch is set to the accessory
position
Notes
If there is no accessory position, connect to the +12 V power
(battery) terminal which is energized at all times.
Be sure to first connect the black ground (earth) lead to a common
ground (earth) point.
If your car has a built-in FM/AM antenna (aerial) in the rear/side
glass, see “Notes on the control and power supply leads.”
To the +12 V power terminal which is energized
at all times
Be sure to first connect the black ground (earth) lead to a common
ground (earth) point.
To the parking brake switch cord
To an auxiliary device such as a portable media
player, game console, etc. (not supplied)
Tip
You can use an RCA cord (not supplied) to connect auxiliary devices.
To the +12 V power terminal of the car’s rear lamp
lead (only when connecting the rear view camera)
Notes on the control and power supply leads
REM OUT lead (blue/white striped) supplies +12 V DC when you turn on
the tuner.
If your car has built-in FM/AM antenna (aerial) in the rear/side glass,
connect REM OUT lead (blue/white striped) or the accessory power
supply lead (red) to the power terminal of the existing antenna (aerial)
booster. For details, consult your dealer.
A power antenna (aerial) without a relay box cannot be used with this
unit.
Memory hold connection
When the yellow power supply lead is connected, power will always be
supplied to the memory circuit even when the ignition switch is turned off.
*
1
Speaker impedance: 4 – 8 ohms × 4
*
2
For details on installing the microphone, see “Installing the microphone
()” on the reverse side.
*
3
Whether in use or not, route the microphone input cord such that it does
not interfere with driving. Secure the cord with a clamp, etc., if it is
installed around your feet.
*
4
RCA pin cord (not supplied)
*
5
For details on connecting to the parking brake switch cord, see
“Connecting the parking brake lead ()” on the reverse side.
*
6
The sound is output from this terminal only when ZONE x ZONE is
activated. This terminal outputs a fixed level regardless of the volume
control of the unit.
*
7
A separate adaptor may be required.
*
8
Not supplied.
Cautions
Run all ground (earth) leads to a common ground
(earth) point.
This unit is designed for negative ground (earth) 12 V
DC operation only.
Do not disassemble or modify the unit.
Do not install in locations which interfere with airbag
operation.
Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).
Before making connections, turn the car ignition off to
avoid short circuits.
Connect the yellow and red power supply leads only
after all other leads have been connected.
Be sure to insulate any loose unconnected leads with
electrical tape for safety.
Do not press on the LCD when installing the unit.
Install the unit with the monitor facing straight forward;
do not install it at a slanted angle.
Notes on the power supply lead (yellow)
When connecting this unit in combination with other
stereo components, the amperage rating of the car
circuit to which the unit is connected must be higher
than the sum of each component's fuse amperage rating.
If no car circuits are rated high enough, connect the unit
directly to the battery.
Parts list
The numbers in the list correspond to those in the
instructions.
The bracket is attached to the unit before shipping.
Before mounting the unit, use the release keys to
remove the bracket from the unit. For details, see
“Removing the bracket ()” on the reverse side of the
sheet.
Keep the release keys for future use as they are
also necessary if you remove the unit from your
car.
Assemble the parts of the microphone before use. For
details, see “Installing the microphone ()” on the
reverse side.
Caution
Handle the bracket carefully to avoid injuring your
fingers.
Catch
Note
Before installing, make sure that the catches on both sides of the bracket
are bent inwards 3.5 mm (
5
/32 in). If the catches are straight or bent
outwards, the unit will not be installed securely and may spring out.
Equipment used in illustrations (not supplied)
× 8
× 2
c
b
a
From car antenna (aerial)
REM OUT
Max. supply current: 0.4 A
Fuse (10 A)
Blue/white striped Red
Yellow
White
Green
Purple
White/black striped
Gray/black striped
Green/black striped
Gray
Left
Right
Left
Right
Black
Purple/black striped
*
5
*
8
Light green
PARKING BRAKE
ILLUMINATION
Orange/white striped
*
4
*
4
*
4
*
4
*
4
FRONT AUDIO
OUT
SUB OUT
REAR OUT
Z×Z L
/
R
REAR AUDIO
OUT
A
B
Video camera*
RC-202IPV*
* not supplied
*
2
Notes on speaker connection
Before connecting the speakers, turn the unit off.
Use speakers with an impedance of 4 to 8 ohms, and with adequate
power handling capacities to avoid damage.
Do not connect the speaker terminals to the car chassis, or connect the
terminals of the right speakers with those of the left speakers.
Do not connect the ground (earth) lead of this unit to the negative (–)
terminal of a speaker.
Do not attempt to connect the speakers in parallel.
Connect only passive speakers. Connecting active speakers (with
built-in amplifiers) to the speaker terminals may damage the unit.
To avoid a malfunction, do not use the built-in speaker leads installed in
your car if they feature a common negative (–) lead for the right and left
speakers.
Do not connect the unit’s speaker leads to each other.
Notes on connection
If “Output connection failure.” appears in the display, make sure the
speaker and amplifier are connected correctly.
To use the monitor for the rear seats, connect the parking brake switch
cord to the ground (earth).
*
4
MonitorPower amplifier
Rear view camera
Rear speaker
iPod
Front speaker
Subwoofer Smartphone
*
1
1
2
Summary of Contents
Page 1 - AV Center
4-419-668-54(1)Installation/ConnectionsAV CenterXAV-601BTAUX1 INAUX2 AUDIOINREVERSE INZxZ L / R*6SUB OUTAUX1 AUDIOINFRONTAUDIO OUTREARAUDIO OUTMIC IN*
Page 2
PrecautionsChoose the installation location carefully so that the unit will not interfere with normal driving operations.Avoid installing the u
Related products and manuals for Motorcycle Accessories Sony XAV-601BT
(11 pages)
(4 pages)
(2 pages)© 2020, manymanuals.com. All rights reserved. | 0.906 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals