Sony MZ-N707 User Manual Page 19

  • Download
  • Add to my manuals
  • Print
  • Page
    / 240
  • Table of contents
  • TROUBLESHOOTING
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 18
19-GB
About the DSP TYPE-R for ATRAC
TYPE-R is a high-level Sony specification
used in the Digital Signal Processor (DSP),
which is heart of the MiniDisc sound. This
technology gives the MiniDisc recorder twice
the signal processing capability as previous
MiniDisc Walkman models, producing a sound
quality close to that of MiniDisc decks. This
unit supports the TYPE-R function only
during recording or playback in normal stereo
(or monaural) mode. It does not support this
function in MDLP mode, or during the
checking out of audio data from the computer
in normal stereo (or monaural) mode using
OpenMG Jukebox.
Notes
The pause function cannot be turned on or off
manually during synchro-recording. Press x
to stop recording.
Do not change SYNC REC setting while
recording. Recording may not be done
properly.
Even when there is no recorded sound on the
sound source, there may be cases when
recording does not pause automatically during
synchro-recording due to the noise level
emitted from the sound source.
If a silent portion is encountered for
approximately 2 seconds during synchro-
recording from a sound source other than a
CD or an MD, a new track mark is
automatically added at the point where the
silent portion ends.
Synchro-recording cannot be done if the
connecting cord is not an optical cable, or if
the cable is connected to the MIC (PLUG IN
POWER) jack.
You cannot change the recording mode during
recording.
Data Save or TOC Edit flashes while data
of the recording (the tracks start and end
points, etc.) is being recorded. Do not move
the recorder or disconnect the power source
while the indication is flashing in the display.
The lid does not open until TOC Edit
disappears in the display.
If the power supply is disrupted (i.e. the
battery is removed or becomes exhausted or
the AC power adaptor is disconnected) during
a recording or editing operation, or while
TOC Edit appears in the display, then it will
not be possible to open the lid until power is
restored.
You can make a digital recording only from an
optical type output.
When recording from a portable CD player,
set the CD player to pause, and then do the
recording procedure on the recorder.
Note the following when recording from a
portable CD player:
Some portable CD players may not be
capable of digital out when the AC power
adaptor is disconnected. If this is the case,
connect the AC power adaptor to the
portable CD player and use it on AC power
as the power source.
On some portable CD players, optical
output may not be possible when using an
anti-skip function (e.g., ESP* or G-
PROTECTION). If this is the case, turn off
the anti-skip function.
Electronic Shock Protection
z
When there is no sound from the player for
more than 3 seconds during synchro-
recording, the recorder goes into the standby
mode automatically. When the sound comes
from the player again, the recorder resumes
synchro-recording. If the recorder is kept in
the standby mode for 5 minutes or longer, the
recorder stops automatically.
For longer recording, follow step 1 of Long-
time recording (MDLP) (page 26) to select
the recording mode, and then start the
procedure of synchro-recording.
LINE IN (OPTICAL) jack is for both digital
and analog input. The recorder automatically
recognizes the type of line cable and switches
to digital or analog input.
The recording level is adjusted automatically.
To adjust the level manually, see Adjusting
the recording level manually (Manual
Recording) (page 32).
You can monitor the sound during recording.
Connect the supplied headphones/earphones
with remote control to i and adjust the
volume by pressing VOL +/. This does not
affect the recording level.
Page view 18
1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 239 240

Comments to this Manuals

No comments