LCD Data Projector4-080-673-15(1)VPL-FE110UVPL-FE110MOperating Instructions 2000 Sony Corporation• The PDF data of the Operating Instructions, Instal
10Control panel+–LIGHTONSTANDBYPIC AUDIOVIDEOPOWER SAVINGCOVER FAILFAN FAILLAMP FAIL1234HIGH TEMPSELECTVOLUMEINPUT A INPUT B INPUT CAPAMENUENTERRESETR
117 INPUT SELECT keysSelect the input signal.VIDEO: Selects the video signal input from theVIDEO or S VIDEO connectors and the audiosignal input from
12RearR/R-Y YC8VIDEO8VIDEOVIDEOAUDIOINVIDEOG/YB/B-YSYNC/HDVDAUDIOINL(MONO)LRLR(MONO)RRS-232CRS-422ARS-232C/422A RS-485IN OUT IN OUTLIGHTAPAVIDEOINPUT
135 Signal interface board attachment part(INPUT B)Optional signal interface board can be attachedaccording to your requirements. If you install the I
14Remote CommanderThe Remote Commander can be used as a wireless or wired RemoteCommander. The keys on the Remote Commander with the same namesfunctio
157 Transmission indicatorThe light goes on each time a key is pressed. If theindicator does not light, replace the batteries.8 LIGHT buttonIlluminat
16Battery installation1 Push to open the lid.2 Install three R6 (size AA) batteries (supplied) withthe polarities correctly aligned.3 Replace the lid.
17Do not install the projector in an ill-ventilated placeThe projector is equipped with ventilation holes for intakeon the bottom and front and ventil
18R/R-YYC8VIDEO8VIDEOVIDEOAUDIOINVIDEOG/YB/B-YSYNC/HDVDAUDIOINL(MONO)LRLR(MONO)RRS-232CRS-422ARS-232C/422ARS-485INOUTINOUTLIGHTAPAVIDEOINPUT AINPUT BI
19INPUT CPC CARDINPUT BINPUT A0 0INPUT C INPUT BINPUT A VIDEOAUDIO OUTREMOTE CONTROL S TRIGDEVICE INDEX+–KEYBOARDMOUSEConnecting to LANThis section de
2WARNINGTo prevent fire or shock hazard, do notexpose the unit to rain or moisture.To avoid electrical shock, do not open thecabinet. Refer servicing
200 0INPUT CPC CARDINPUT BINPUT A VIDEOAUDIO OUTREMOTE CONTROL S TRIGDEVICE INDEX+–KEYBOARDMOUSEConnection of wireless LAN PC cardRearto hub/routerWir
21Connecting with a Computer or a VCRThis section describes how to connect the projector with a computer, VCR,and external active speakers.For details
22Projecting1 Press the ON key on the Remote Commander or the control panel.The ON indicator lights in green.2 Turn on the power of equipment connecte
23When you input the signal from equipment connected to the PC-3000signal interface switcher (not supplied), set the SWITCHER/VIDEOMEMORY/INDEX select
247 Press the SHIFT key then the arrow keys on the Remote Commanderor the control panel to adjust the vertical position of the picture.“PICTURE SHIFT”
25Using the MenuAdjustments and settings using the menuThe projector is equipped with an on-screen menu formaking various adjustments and settings.Una
26The PICTURE CTRL MenuThe PICTURE CTRL menu is used for adjusting thepicture. Unadjustable items are not displayed in themenu.PICTURE CTRLCONTRAST:B
27The INPUT SETTING MenuThe INPUT SETTING menu is used to change thesettings of the input signal. Unadjustable items, whichvary according to the input
28The INPUT SETTING MenuInput signals and adjustable/setting itemsItemDOT PHASESIZESHIFTSCAN CONVASPECTH FILTERBLANKINGY: Adjustable/can be setN: Not
29MemoryPreset signalfH fVSyncHorizontalNo.(kHz) (Hz) size391600 × 1200UXGA VESA 60 75.00 60.00H-pos V-pos 168940 UXGA VESA 65 81.91 65.53H-pos V-pos
3Pour les utilisateurs au CanadaCet appareil numérique de la classe A est conforme à lanorme NMB-003 du Canada.La prise doit être près de l’appareil e
30The SET SETTING MenuThe SET SETTING menu is used for changing theinitial settings of the projector. Unadjustable items arenot displayed in the menu.
31The SIGNAL SELECT MenuThe SIGNAL SELECT Menu is used for selecting theinput signal.Depending on the interface board installed in theprojector, some
32Connecting a BNC connectorConnecting 15k RGB/Component EquipmentNoteSwitch the input signal with the INPUT-A item in the SIGNAL SELECTmenu.For detai
330INPUT C INPUT BINPUT A VIDEOAUDIO OUTREMOTE CONTROL S TRIGDEVICE INDEX+–1KEYBOARDMOUSE:OUT PUTSW NORS-232C/422AREMOTERS-232CRS-422ARS-485 INRS-485
34Confirming the System ConstructionAfter all the connections are complete, confirm that equipment of thesystem is properly setup.1 Connect the AC cor
35Setting the Index Numbers01Ten’s digit Unit’s digitWhen you connect multiple projectors in your system,you have to set the group index and device in
36Notes on connections when two or moreswitchers are used• Mount the IFB-12A interface board to the slot 1 ofthe number n switcher and connect the out
37Replacing the LampWhen the lamp has burnt out, the LAMP FAILindicators at the rear of the projector light. In this case,replace the lamp with a new
384 Replace the lamp cover and push to tighten the twoscrews to fix the cover.To reset the use time of the lamps in themessage display window1 Plug in
39If the projector appears to be operating erratically, try to diagnose andcorrect the problem, using the following guide. If the problem still persis
40SymptomThe image from INPUT C does notappear.“NO INPUT” is displayed.The PJ COM connectors do notfunction.The mouse or keyboard does notfunction.The
41Caution messagesUse the list below to check the meaning of the messages displayed on thescreen.MessageHigh Temperature!Power off in 1 min.Frequency
42SpecificationsOptical characteristicsProjection system 3 LCD panels, 1 lens, 3-primarycolor optical shutter systemLCD panel 1.8-inch SXGA LCD panel,
43VD: Vertical sync: 0.6–8 Vp-p,high impedance, sync positive/negativeAUDIO IN: Phono type (stereo)500 m Vrms, impedance morethan 47 kilohmsHDTV/DTV (
44Optional accessoriesProjector Lamp LMP-Q130 (for replacement)Projector Lamp LMP-S120 (for replacement)Interface BoardIFB-12A (Analog RGB/component/H
45RS-422A1 GND Ground 6 GND Ground2TXTransmit 7 TX Transmit3 RX Receive 8RXReceive4 GND Ground 9 GND Ground5NCPJ COM connector (D-sub 9-pin, female)1
46AAdjusters 9Adjustingpicture 26picture size/shift 27zoom 23Air filter 38ASPECT 27AUDIO MUTING 24BBatteryInstallation 16notes 16BLANKING 2
Sony Corporation Printed in Japan
5Table of ContentsOverviewPrecautions ... 6Features...
6PrecautionsOn safety• Check that the operating voltage of your unit isidentical with the voltage of your local power supply.If voltage adaptation is
7FeaturesOverviewHigh brightness, high picture quality• High brightnessAdopting four newly developed 120 W UHP lampsand a LCD panel with micro lens pr
8Location and Function of ControlsFrontq;3791285461 Speaker2 Lens mount partWhen attaching the optional lens, consult with theSony service personnel.3
9Using the carrying handlesPull out to use for carrying the projector. To put awaythe handle, slide the handle lever forward.Using the adjusters1 Pres
Comments to this Manuals