SD INTERFACE BOARD
HFBK-SD1
Sony Corporation 2005
Printed in Japan 2008.11.13
3-869-802-06(1)
•
ご使用にあたっては、設置先の機器に付属のオペレーションマニュア
ルの「安全のために」をよくお読みください。
•
装着のしかたは、設置先の機器に付属のオペレーションマニュアルの
「オプション基板の装着」をご覧ください。
For installation instructions, refer to “Mounting an Optional Board”
in the Operation Manual supplied with the product in which this
board is to be mounted.
OPERATION MANUAL
[Japanese/English]
電気製品は、安全のための注意事項を守らないと、
火災や人身事故になることがあります。
日本語
概要
HFBK-SD1は、以下の機器に装着して使用するオプションボードです。
• HDカメラインターフェースユ ニットHFU-X310
• HD 3CCDカラービデオカメラBRC-H700
• HDオプチカルマルチプレックスユニットBRU-H700
装着した機器に接続したカラービ デ オカメラからの 映 像をダウンコンバートし
て、SD-SDI信号およびアナログ信号に変換して出力します。出力信号のアス
ペクト比 には 、16:9レターボックス、4:3エッジクロップ(切り出し )、スクイーズを
選択できます。アナログ信 号は、コン ポ ー ネ ント/コンポジット/ Sビ デオも出力
可能です。
エンベデッドオーディオとタイムコード対応のHFU-X310に装着したときは、
HFU-X310に入力されたHD-SDI信号のエンベデッドオーディオとタイムコード
をSD-SDI 信号に重畳して出力します。
ご注意
タイムコードは 下記 のライン(固定)に出力されます。
映像信号が
NTSC
(
59.94i
)のとき 映像信号が
PAL
(
50i
)のとき
LTC: 13 ライン LTC: 9 ライン
VITC1: 12 ライン、14 ライン VITC1: 8ライン、10 ライン
VITC2: 275ライン、277 ライン VITC2: 321ライン、323ライン
各部の名称と働き
1
MONITOR
(モニター出力)端子(
D-sub 9
ピン)
アナログ映 像出 力で す。DIPスイッチの設定によって、出力信号を切り換 える
ことが でき ます 。
2
DIP
スイッチ
信号の出力条件を設定します。
ご注意
装着した機器の電源を切ってからDIPスイッチを切り換えてください 。
スイッチ
1
(
Sync/Setup
)
スイッチ 3でMONITOR端子の出力にRGBを選択しているときは、出力信号
に同期信号を付加するかどうかを選択します。
上( Add Sync):同期 信号が 付加されます。(工場設定)
下( No Sync):同期信号を付加しません。
スイッチ 3でMONITOR端子の出力にYPbPrを選択しているときは、出力信
号に 7.5%のセットア ップ を 付 加 す るか どうかを 選 択 し ます 。
上( No Setup):セットア ップ を 付 加し ませ ん 。(工場設定)
下( Add Setup):セットアップ が 付 加され ます 。
ご注意
• セットアップ の付加は、映像信号がNTSC(59.94i)のときのみ有効です。
• セットアップ は 、MONITOR 端子とVIDEO 端子の出力に付加されます。
• BRC-H700またはBRU-H700に装着の際は、装着する機器がセットアップ 付
加機能対応バージョンである必要があります。
◆対応バージョンかどうかは、お買い上げ店またはソニーの営業担当者にご確認
ください。
スイッチ
2
(
Sync on G
)
スイッチ 3でMONITOR端子の出力にRGBを、スイッチ 1 で同期信号付加
(Add Sync)を選択しているとき、同期信号をR/G/B各信号に付加するか、G
信号にのみ付加するかを選択します。
上( Sync on ALL):R/G/B各信号に同期信号が付加されて出力されます。
(工場設定)
下( Sync on G):G 信号に同期信号が付加されて出力されます。
スイッチ
3
(
RGB/YPbPr
)
MONITOR端子のコンポーネント出 力を切り 換えます。
上( YPbPr):コン ポ ー ネント信 号 を出 力します。(工場設定)
下( RGB):RGB信号を出力します。
スイッチ
4
(コンポジット
/S
ビデオ)
MONITOR端子の 6ピンから出力される信号を切り換えます。
上(コ ンポ ジ ット):ア ナロ グコン ポジット信 号 を 出 力します。(工場設定)
下(Y): S ビ デ オ 信 号 の Y 信 号を 出 力しま す 。このとき9ピンからC 信号が出
力されます。
スイッチ
5
(
16:9/4:3
)
出力する信号のアスペクト比 を 選 択し ます 。
上( 16:9):ア スペ クト比 16:9(レターボックス)になります。スイッチ 6 は 無 効
になります。(工場設定)
下( 4:3):ア スペ クト比 4:3になります。スイッチ 6 で エッジクロップ か スクイー
ズを選択します。
スイッチ
6
(
Crop/Squeeze
)
スイッチ 5 でアスペクト比 4 : 3 を 選 択 した とき 有 効 になりま す。
上( Crop):エッジクロップが出力されます。(工場設定)
下( Squeeze):スクイーズが出力されます。
スイッチ
7
(
Delay
)
同期信号に対して映像出力をディレイさせるかどうかを 選択します。
上( No Delay):ディレイなし( 工 場 設定)。
下( Delay):8 9 または 9 0 ライン(HD)ディレイさせます。
スイッチ
8
(
89H/90H
)
スイッチ 7 で ディレイ選択 時に映 像出 力と同 期信 号との位 相差を設 定します。
上( 89H):8 9 ライン(HD)ディレイさせます( 工 場 設定)。
下( 90H):9 0 ライン(HD)ディレイさせます。
ご注意
スイッチ 7、8 は、ディレイ機能対応バージョンの HD カメラインターフェースユ
ニットHFU-X310に装着したときのみ有効です。
◆スイッチ 7、8の機能について詳しくは、 HFU-X310のオペレーションマニュアル
をご 覧ください。
3
VIDEO
(アナログコンポジット映像)端子(
BNC
型)
画像確認用にアナログコンポジット信 号 を 出 力し ま す。DIPスイッチ の 設 定 に
よってアスペクト比 を 選 択し ます。
4
SDI
(デジタル出力)端子(
BNC
型)
ダウンコンバートしたSD-SDI信号を出力します。DIPスイッチ の 設 定 に よっ て、
アスペクト比 を 選 択 し ま す 。
For the customers in the U.S.A.
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
You are cautioned that any changes or modifications not expressly
approved in this manual could void your authority to operate this
equipment.
All interface cables used to connect peripherals must be shielded in
order to comply with the limits for a digital device pursuant to
Subpart B of Part 15 of FCC Rules.
This device complies with part 15 of FCC Rules.
Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may
cause undesired operation.
For customers in Canada
This Class A digital apparatus complies with Canadian ICES-003.
For the customers in Europe
This product with the CE marking complies with the EMC Directive
issued by the Commission of the European Community.
Compliance with this directive implies conformity to the following
European standards:
• EN55103-1: Electromagnetic Interference (Emission)
• EN55103-2: Electromagnetic Susceptibility (Immunity)
This product is intended for use in the following Electromagnetic
Environment(s):
E1 (residential), E2 (commercial and light industrial),
E3 (urban outdoors) and E4 (controlled EMC environment, ex. TV
studio).
The manufacturer of this product is Sony Corporation, 1-7-1 Konan,
Minato-ku, Tokyo, Japan.
The Authorized Representative for EMC and product safety is Sony
Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart,
Germany.
1 MONITOR端子
2 DIPスイッチ (カバー内)
HFBK-SD1
MONITOR VIDEO SDI
4 SDI端子
3 VIDEO端子
Comments to this Manuals