Sony STR-DA777ES User Manual download pdf (Page 21)

Hooking Up and Setting Up the Speaker System

Adjusting the speaker volume

Use the remote while seated in your listening position to

adjust the volume of each speaker.

For more information regarding remote control

operations, refer to the separate manual “Remote

Commander” supplied with this unit.

1 Press 1/u to turn on the receiver.

2 Touch SOUND FIELD on the supplied remote to

display the SOUND FIELD screen.

3 Touch LEVEL on the supplied remote to display the

LEVEL screen.

4 Touch TEST TONE on the supplied remote.

5 Touch + on the remote.

You will hear the test tone from each speaker in

sequence.

6 Adjust the volume level so that the volume of the

test tone from each speaker sounds the same

when you are in your main listening position.

• To adjust the balance of the front right and front left

speakers, use the front balance controls on the

remote (or FRONT (L/R) in the LEVEL menu (page

42)).

• To adjust the balance of the rear right and rear left

speakers, use the rear balance control in the remote

(or REAR (L/R) in the LEVEL menu (page 42)).

• To adjust the volume level of the center speaker, use

the center level control on the remote (or CENTER

LEVEL in the LEVEL menu (page 42)).

• To adjust the volume level of the rear speakers, use

the rear level control on the remote (or REAR

LEVEL in the LEVEL menu (page 42)).

7 Touch TEST TONE on the remote again and set OFF

the test tone.

You can adjust the volume level of all speakers at the same

time

Turn MASTER VOLUME on the main unit or touch MASTER

VOLUME +/– on the remote.

You can output the test tone from the speaker of your choice

Normally, the test tone is output from each speaker in sequence.

However, you can use the LEVEL menu to output the test tone

from one specific speaker (see page 42). After you have touched

TEST TONE, touch +/– repeatedly to select “fix [XXX]”or “[XXX]

fix”. The test tone is output from the selected speaker.

p Front speaker roll off frequency

FRONT SP > XXXHz

Initial setting : > 80 Hz

This setting lets you select the roll off frequency for the

low cut filter of the front (left and right) speakers when

the front speakers are set to “SMALL”.

• The bass frequencies lower than the cut off frequency

are divided by the bass redirection circuitry and output

from the sub woofer or other “LARGE” speakers. In

order to prevent clipping, frequencies below the cut off

frequency are not output from the front speakers.

p Center speaker roll off frequency

CENTER SP > XXXHz

Initial setting : > 80 Hz

This setting lets you select the roll off frequency for the low cut filter

of the center speaker when the center speaker is set to “SMALL”.

• The bass frequencies lower than the cut off frequency

are divided by the bass redirection circuitry and output

from the sub woofer or other “LARGE” speakers. In

order to prevent clipping, frequencies below the cut off

frequency are not output from the center speaker.

p Rear speaker roll off frequency

REAR SP > XXXHz

Initial setting : > 80 Hz

This setting lets you select the roll off frequency for the

low cut filter of the rear (left and right) speakers when the

rear speakers are set to “SMALL”.

• The bass frequencies lower than the cut off frequency

are divided by the bass redirection circuitry and output

from the sub woofer or other “LARGE” speakers. In

order to prevent clipping, frequencies below the cut off

frequency are not output from the rear speakers.

About the roll off frequency parameters

These parameters are designed to allow you to prevent clipping

by eliminating output of low-bass frequencies from “SMALL”

speakers. Be sure to set the roll off frequency so that clipping

does not occur from the respective speaker.

p LFE high cut filter

LFE HIGH CUT [STD]

Initial setting: STD (=120 Hz)

This setting lets you select the cutoff frequency of the LFE

channel High Cut Filter. Normally, this should set to STD.

When using a passive subwoofer powered by a separate power

amplifier, it may be better to change the cutoff frequency. When

this is the case, use a setting other than STD.

p Distance unit

DIST.UNIT [feet]* [meter]

Initial setting : feet* (meter)

Lets you select either feet or meters as the unit of measure for

setting distances. 1 foot corresponds to a 1 ms difference.

* U.S.A./Canada models only.

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 186 187

Comments to this Manuals

No comments

Sony STR-DA777ES User Manual Page 21

Comments to this Manuals

Related products and manuals for AV receivers Sony STR-DA777ES