Precautions
•Choose the installation location carefully so
that the unit will not interfere with normal
driving operations.
•Avoid installing the unit in areas subject to
dust, dirt, excessive vibration, or high
temperatures, such as in direct sunlight or near
heater ducts.
•Use only the supplied mounting hardware for
a safe and secure installation.
Mounting angle adjustment
Adjust the mounting angle to less than 20°.
PAL/NTSC select switch (5)
Before installing the unit, set the PAL/NTSC
select switch on the bottom of the unit to “PAL”
or “NTSC” according to the color system of your
country.
When making a digital
connection (6)
When connecting to a digital amplifier or audio
device equipped with a Dolby digital decoder,
connect the optical cable to the optical adaptor
first, then connect the optical adapter to the
DIGITAL OUT on the back panel.
Notes
•When you wish to disconnect the optical cable,
simply push in on both sides of the connector.
• Be sure to keep the protective cap in a safe place
for future use.
• Do not bend the optical cable too much. If it is
bent in an arc of less than 10 cm in diameter,
sound may not be reproduced.
• Be sure to use an optical cable (not supplied) and
an optical adapter (not supplied) designed for
Sony car audio systems.
• Make sure that the optical cable is securely
plunged to the optical adapter when making
connection.
• Make sure the optical cable does not get
compressed or constricted in any way by
surrounding objects.
• Never let the coupler parts of the connectors get
scratched or become contaminated with dirt.
Mounting example (7)
Installation in a Japanese car
You may not be able to install this unit in some
makes of Japanese cars. In such a case, consult
your Sony dealer.
Note
To prevent malfunction, install only with the
supplied screws 1.
Warning when installing in a car
without ACC (accessory)
position on the ignition key
switch
Be sure to press and hold (OFF) on the unit
until the key illuminations in blue go off after
turning off the engine.
When you press (OFF) only momentarily, the
unit does not turn off and this causes battery
wear.
Reset button (8)
When the installation and connections are
completed, be sure to press the reset button with
a ballpoint pen, etc., to reset the unit.
使用前注意事項
•請仔細選擇安裝位置，以使本機不妨礙正常的
駕駛操作。
•避免將本機安裝在多塵、髒亂、極易受震動的
地方，或者高溫之處，如陽光直射處或暖氣管
道附近。
•為了安裝安全和牢固，安裝時請只使用附送的
零件。
安裝角度的調整
請在 20 度以內調整安裝角度。
PAL/NTSC 選擇開關(5)
安裝本機之前，根據貴國或地區的彩色制式而定，
請將本機後面的 PAL/NTSC 選擇開關設定到“PAL”
或“NTSC”。
進行數位連接時(6)
當連接至帶有杜比數位解碼器的數位放大器或音頻
設備時，請先將光學線纜連接到光學轉接器，然後
將光學轉接器連接到後面板上的 DIGITAL OUT。
註
•
要斷開光學線纜的連接時，只要按一下連接器的兩
側。
•
務必將保護帽放在安全之處以備日後使用。
•
請勿過度彎曲光學線纜。如果將其彎曲成直徑小於
10 cm 的圓弧形，可能無法再現聲音。
•
務必使用專用於 Sony 音頻系統的光學線纜（非附
送）和光學轉接器（非附送）。
•
進行連接時，請確認光學線纜被牢固地插入光學轉接
器中。
•
確認光學線纜未被周圍的物體擠壓。
•
切勿刮傷連接器的接頭部分或使之積滿灰塵。
安裝示例(7)
安裝在日本產汽車上
有的日本產汽車不能安裝本機。在這種情形下，請
您向當地的 Sony 經銷商諮詢。
註
為防止發生故障，安裝時只能使用附送的螺絲
1
。
安裝在點火鑰匙開關上沒有 ACC
（附件）位置的汽車上時的警告
在關掉汽車發動機之後，務必按住本機上的 (OFF)
不放，直至藍色的鍵照明熄滅。
如果只短暫地按一下 (OFF)，將不會關閉本機從
而浪費電池。
復原按鈕(8)
當安裝和連接完畢後，務必用圓子筆等按壓復原按
鈕，復原本機。
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals