Sony ICF-C8WM User Manual download pdf

English

WARNING

To reduce the risk of fire or electric shock, do

not expose this apparatus to rain or

moisture.

To reduce the risk of fire, do not cover the

ventilation of the apparatus with newspapers,

tablecloths, curtains, etc. And do not place lighted

candles on the apparatus.

To reduce the risk of fire or electric shock, do not

expose this apparatus to dripping or splashing,

and do not place objects filled with liquids, such

as vases, on the apparatus.

Do not install the appliance in a confined space,

such as a bookcase or built-in cabinet.

Do not expose the batteries (battery pack or

batteries installed) to excessive heat such as

sunshine, fire or the like for a long time.

As the main plug is used to disconnect the unit

from the mains, connect the unit to an easily

accessible AC outlet. Should you notice an

abnormality in the unit, disconnect the main plug

from the AC outlet immediately.

The unit is not disconnected from the AC power

source (mains) as long as it is connected to the

wall outlet, even if the unit itself has been turned

off.

CAUTION

Danger of explosion if battery is incorrectly

replaced. Replace only with the same type.

Notice for customers: the following

information is only applicable to equipment

sold in countries applying EU directives

The manufacturer of this product is Sony

Corporation, 1-7-1 Konan, Minato-ku, Tokyo,

Japan. The Authorized Representative for EMC

and product safety is Sony Deutschland GmbH,

Hedelfinger Strasse 61, 70327 Stuttgart, Germany.

For any service or guarantee matters please refer

to the addresses given in separate service or

guarantee documents.

Precautions



Operate the unit on the power source specified

in “Specifications.”



To disconnect the AC power cord (mains lead),

pull it out by the plug, not the cord.



Since a strong magnet is used for the speaker,

keep personal credit cards using magnetic coding

or spring-wound watches away from the unit to

prevent possible damage from the magnet.



Do not leave the unit in a location near a heat

source such as a radiator or airduct, or in a

place subject to direct sunlight, excessive dust,

mechanical vibration, or shock.



Allow adequate air circulation to prevent

internal heat build-up. Do not place the unit on

a surface (a rug, a blanket, etc.) or near

materials (a curtain) which might block the

ventilation holes.



Should any solid object or liquid fall into the unit,

unplug the unit and have it checked by qualified

personnel before operating it any further.



To clean the casing, use a soft cloth dampened

with a mild detergent solution.



Never touch the wire of the external FM aerial

during a thunderstorm. Furthermore,

immediately disconnect the AC power cord

from the radio.

NOTES ON LITHIUM BATTERY



Wipe the battery with a dry cloth to assure a

good contact.



Be sure to observe the correct polarity when

installing the battery.



Do not hold the battery with metallic tweezers,

otherwise a short-circuit may occur.

Disposal of Old Electrical &

Electronic Equipment (Applicable

in the European Union and other

European countries with separate

collection systems)

This symbol on the product or on its packaging

indicates that this product shall not be treated as

household waste. Instead it shall be handed over

to the applicable collection point for the recycling

of electrical and electronic equipment. By

ensuring this product is disposed of correctly, you

will help prevent potential negative consequences

for the environment and human health, which

could otherwise be caused by inappropriate waste

handling of this product. The recycling of

materials will help to conserve natural resources.

For more detailed information about recycling of

this product, please contact your local Civic

Office, your household waste disposal service or

the shop where you purchased the product.

Applicable accessory: Remote Commander.

Disposal of waste batteries

(applicable in the European

Union and other European

countries with separate

collection systems)

This symbol on the battery or on the packaging

indicates that the battery provided with this

product shall not be treated as household waste.

On certain batteries this symbol might be used in

combination with a chemical symbol. The

chemical symbols for mercury (Hg) or lead (Pb)

are added if the battery contains more than

0.0005% mercury or 0.004% lead.

By ensuring these batteries are disposed of

correctly, you will help prevent potentially

negative consequences for the environment and

human health which could otherwise be caused

by inappropriate waste handling of the battery.

The recycling of the materials will help to

conserve natural resources.

In case of products that for safety, performance or

data integrity reasons require a permanent

connection with an incorporated battery, this

battery should be replaced by qualified service

staff only.

To ensure that the battery will be treated properly,

hand over the product at end-of-life to the

applicable collection point for the recycling of

electrical and electronic equipment.

For all other batteries, please view the section on

how to remove the battery from the product

safely. Hand the battery over to the applicable

collection point for the recycling of waste

batteries.

For more detailed information about recycling of

this product or battery, please contact your local

Civic Office, your household waste disposal

service or the shop where you purchased the

product.

If you have any questions or problems concerning

your unit, please consult your nearest Sony dealer.

Note

When you replace the battery, do not disconnect

the plug from the AC outlet. Otherwise, the

calendar, current time, alarm and station presets

will be initialized.

Reset button







CR2032

If the time in the display is

incorrect after the battery is

changed (Reset)

Press the reset button with a pointed instrument.

The reset button is in the small hole located near

the battery holder.

Compatible

“WALKMAN” models

Use the Oval attachment (supplied with your

“WALKMAN”) when you connect it to this unit.

If the Oval attachment is not supplied with your

“WALKMAN,” use one of the attachments

supplied with this unit. “WALKMAN” models

compatible with this unit are as follows.

Models using the Oval attachment

(supplied with your “WALKMAN”)

NWZ-E440 series: NWZ-E443/E444/E445/

E443K/E444K

NWZ-S540 series: NWZ-S544/S545

Models using the Type A attachment

(supplied with this unit)

NWZ-E430 series: NWZ-E435F/E436F/E438F

NWZ-S630 series: NWZ-S636F/S638F/S639F/

S636FK

NWZ-S730 series: NWZ-S736F/S738F/S739F

NWZ-A720 series: NWZ-A726/A728/A729

NW-A800 series: NW-A808/A806/A805

NWZ-A810 series: NWZ-A815/A816/A818

NWZ-A820 series: NWZ-A826/A828/A829/

A826K/A828K/A829K

Models using the Type B attachment

(supplied with this unit)

NWZ-S510 series: NWZ-S515/S516

NWZ-S610 series: NWZ-S615F/S616F/S618F

NWZ-S710 series: NWZ-S715F/S716F/S718F

NWZ-X1000 series: NWZ-X1050/X1060

Tip

The type of attachment is located on the bottom.

On copyrights



“WALKMAN” and

are

registered trademarks of Sony Corporation.



All other trademarks and registered trademarks

are trademarks or registered trademarks of

their respective holders. In this manual,

™ and ® marks are not specified.

Compatible Sony

Ericsson Phone models

Compatible Sony Ericsson Phone models are as

follows.

Model(s) Available

function(s)

C510/C510a/C702/C702a/

C902/C903

G700/G700Busir/G900

K530i/K550i/K550im/

K610i/K610im/K618i/

K770i/K790a/K800i/

K810i

S500i

T650i/T700/T707/TM506

V630i

W508/W580i/W595/

W610i/W660i/W710i/

W760a/W760i/W850i/

W880i/W980/W995/

W995a

Z610i/Z710i

Alarm/

Music

playback/

Battery

charge

C901/C905

G502/G705/G705u

K310i/K320i/K510i/K630i/

K660i/K750i/K850i

M600i

P1i/P990i

V640i

W200i/W300i/W700i/

W705/W810i/W890i/

W902/W910i/W950i/

W960i

Z530i/Z550a/Z550i/Z558i

Z750i/Z770i

Music

playback/

Battery

charge

F305

J110i/J120i

K200i/K330

R300

S302/S312

T250i/T280i/T303

W302/W350i/W380i/W395

Z310a/Z310i/Z555i

Battery

charge

Features



Clock Radio with “WALKMAN” / Sony

Ericsson Phone compatible



Wake or Sleep to “WALKMAN” / Sony Ericsson

Phone / Radio



Easy to set A-B alarm



2-5-7 day alarm



LCD Brightness control



Wireless Remote commander

Connecting the aerial

To connect the AM loop

aerial

The shape and the length of the aerial is designed

to receive AM signals. Do not dismantle or roll up

the aerial.

1 Remove only the loop part from the

plastic stand.

2 Set up the AM loop aerial.

3 Connect the cords to the AM aerial

terminals.

Cord (A) or cord (B) can be connected to

either terminal.

Only insert up

to here.

Insert the cord while

pushing down the

terminal clamp.

4 Make sure the AM loop aerial is

connected firmly by pulling softly.

Adjusting the AM loop aerial

Find a place and an orientation that provide good

reception.



Do not place the AM loop aerial near the unit

or other AV equipment, as noise may result.

Tip

Adjust the direction of the AM loop aerial for best

AM broadcast sound.

Preparing the remote

commander

Before using the card remote commander for the

first time, remove the insulation film.

When to replace the battery

With normal use, the battery (CR2025) should

last for about six months. When the remote

commander no longer operates the unit, replace

the battery with a new one.

CR2025



Notes



Do not attempt to charge the battery.



If you are not going to use the remote

commander for a long time, remove the battery

to avoid any damage that may be caused by

leakage and corrosion.

About the backup

battery

To keep accurate time, this unit contains a

CR2032 battery as a backup power source.

The battery keeps the clock and the alarm

operating in the event of a power interruption.

Note for customers in Europe

The clock is preset at the factory, and its memory

is powered by the preinstalled Sony CR2032

battery. If the “0:00” appears in the display when

the unit is connected to AC outlet for the first

time, the battery may be weak. In this case,

consult a Sony dealer. The preinstalled CR2032

battery is considered part of the product, and is

covered by the warranty.

You are required to show “Note for customers in

Europe” (in this instruction) to a Sony dealer in

order to validate the warranty for this product.

Knowing when to replace the

battery

When the battery becomes weak, “” appears in

the display.

If a power interruption occurs while the battery is

weak, the current time and alarm will be

initialized.

Replace the battery with a Sony CR2032 lithium

battery. Use of another battery may cause a fire or

explosion.

Replacing the battery

1 Keep the AC plug connected to the AC

outlet, remove the screw that secures the

battery holder at the bottom of the unit

using a screwdriver, and remove the

battery holder (see Fig.).

Replace a new battery in the battery holder

with the



side facing up

(see Fig.)

3 Insert the battery holder back into the

unit and secure it with the screw

(see Fig.).

4 Press  (play), RADIO BAND, AUDIO IN

or SNOOZE/DATE/SLEEP OFF to turn

“

” off in the display.

Note

The FM frequency display is accurate to within

0.1 MHz. For example, frequency 88.00 and 88.05

MHz will be displayed as “88.0 MHz.”

Tuning in to a station

The unit automatically scans AM or FM stations.

1 Press RADIO BAND to turn on the radio

and select the AM or FM band.

2 Press and hold TUNING + or – (TUNE +

or – on the remote).

+: scans upward through the frequency bands.

–: scans downwards through the frequency

bands.

Scanning starts from the currently-tuned

frequency. When a station is received,

scanning stops.

3 Adjust the volume using VOLUME +

or – (VOL + or – on the remote).

–Preset tuning

You can preset 20 stations for FM and 10 stations

for AM.

Presetting a station

1 Follow steps 1 and 2 in “Manual tuning”

to tune the frequency you wish to preset.

2 Press and hold DISPLAY/MEMORY for

at least 2 seconds.

3 Press PRESET + or – to select the preset

number, then press DISPLAY/MEMORY.

The frequency is stored with the selected

preset number.

Example: The following display appears

when you preset FM 105.8 MHz to preset

number 1 for FM.



The display shows the frequency for about

10 seconds, and then returns to the current

time.

To preset another station, repeat these steps.

Note

If you try to store another station with the same

preset number, the previously stored station will

be replaced.

Tuning in to a preset station

1 Press RADIO BAND to turn on the radio

and select the AM or FM band.

2 Press PRESET + or – to select the desired

preset number.

3 Adjust the volume using VOLUME + or

– (VOL + or – on the remote).

–Auto preset tuning

1 Press RADIO BAND to turn on the radio

and select the AM or FM band.

2 Press and hold RADIO BAND until “AP”

appears in the display.

3 Press DISPLAY/MEMORY.

The unit automatically presets the available

channels in order.

Improving the reception

FM:

Extend the FM wire aerial fully to increase

reception sensitivity.

AM:

nnect the supplied AM loop aerial to the

unit. Rotate the aerial horizontally for optimum

reception.

Notes on radio reception



Keep digital music players or mobile phones

away from the AM loop aerial or the FM aerial,

as this may lead to reception interference.



When you are listening to the radio with a Sony

Ericsson Phone connected to the unit,

interference with radio reception may occur.



When you are listening to the radio while

charging a “WALKMAN” / Sony Ericsson

Phone, interference with radio reception may

occur.

Operating a

“WALKMAN” / Sony

Ericsson Phone

You can enjoy “WALKMAN” / Sony Ericsson

Phone music by connecting to this unit. To use a

“WALKMAN” / Sony Ericsson Phone, refer to the

user’s guide of your “WALKMAN” / Sony

Ericsson Phone.

To select the connector of the

“WALKMAN” / Sony Ericsson

Phone

This unit has two connectors for a “WALKMAN”

and a Sony Ericsson Phone.

Select the connector before using “WALKMAN” /

Sony Ericsson Phone according to the following

procedures.

Note

A “WALKMAN” and Sony Ericsson Phone

cannot be used at the same time.

1 Pull the Docking Tray all the way out.

“WALKMAN” connector

Sony Ericsson Phone

connector

2 Press SELECT to select the

“WALKMAN” or Sony Ericsson Phone

connector.

The indicator turns on to indicate the

“WALKMAN” or Sony Ericsson Phone

connector is activated.

Note

The Sony Ericsson Phone connector is selected by

the default setting.

To operate a “WALKMAN”

1 Choose the “WALKMAN” attachment

that fits your “WALKMAN” (see

“Compatible “WALKMAN” models”).

2 Insert the tab on the left side of the

attachment (A) into the left slot in the

“WALKMAN” connector, and then press

down into the unit (B).

3 Set your “WALKMAN” on the unit.

The connector indicator blinks for a few

seconds and then stays lit.

Notes



The unit cannot operate while the connector

indicator is blinking.



If the indicator does not stay lit, remove the

“WALKMAN” and set again.



When removing the “WALKMAN,” hold the

Docking Tray securely with one hand.

4 Press  (play).

“ ” appears in the display.

The “WALKMAN” begins to play

automatically. You can operate the connected

“WALKMAN” by this unit or the

“WALKMAN” buttons.

5 Adjust the volume using VOLUME + or

– (VOL + or – on the remote).

To Press

Stop playback

OFF

Go to the next track

 (forward)

Go back to the previous

track

 (backward)

Locate a point while

listening to the sound

 (forward) or

 (backward)

while playing and

hold it until you

find the point.

Tip

To remove the “WALKMAN” attachment, press

firmly down on the area marked (ooo) (A), and

remove (B), as shown in the illustration.

To operate a Sony Ericsson

Phone

1 Set your Sony Ericsson Phone on the

unit.

The connector indicator blinks in a few

seconds and then stays lit (green).

When your Sony Ericsson Phone is off, or if it

is listed in “Compatible Sony Ericsson Phone

models”

, the indicator will turn red. In

this case, only battery charge function will be

available (see “To use the unit as a battery

charger”).

Notes



The unit cannot operate while the connector

indicator is blinking.



If the indicator does not stay lit, remove the

Sony Ericsson Phone and set again.



Set Bluetooth function to off on the Sony

Ericsson Phone.

2 Press  (play).

“ ” appears in the display.

The Sony Ericsson Phone begins to play

automatically. You can operate the connected

Sony Ericsson Phone by this unit or the Sony

Ericsson Phone buttons.

Note

If the Sony Ericsson Phone is listed in

“Compatible Sony Ericsson Phone models”

certain operations may not be performed by the

buttons on this unit. In this case, operate with the

buttons on the Sony Ericsson Phone.

3 Adjust the volume using VOLUME + or

– (VOL + or – on the remote).

To Press

Stop playback

OFF

Go to the next track

 (forward)

Go back to the previous

track

 (backward)

Locate a point while

listening to the sound*

 (forward) or

 (backward)

while playing and

hold it until you

find the point.

This function may not be available on some

models. If the function does not work, press

 (play) to cancel.

Notes



The volume may be low when the volume of

Sony Ericsson Phone is set to low. In this case,

adjust the volume of Sony Ericsson Phone.



When removing the Sony Ericsson Phone, hold

the Docking Tray securely with one hand and

tilt the phone forward.

To use the unit as a battery

charger

You can use the unit as a battery charger.

Charging begins when the “WALKMAN” or Sony

Ericsson Phone is connected to the unit.

Charging status appears in the “WALKMAN” or

Sony Ericsson Phone display. For details, see the

user’s guide of your “WALKMAN” or Sony

Ericsson Phone.

Note

A “WALKMAN” and Sony Ericsson Phone

cannot be charged at the same time. Only the

selected device (connector indicator on) can be

charged.

Setting the alarm

This clock radio is equipped with 3 alarm

modes—“WALKMAN” / Sony Ericsson Phone,

radio and buzzer. Before setting the alarm, make

sure to set the clock (see “Setting the clock for the

first time”).

Note

Alarm function is available only for the models

listed in “Compatible Sony Ericsson Phone

models”

To set the alarm

1 Press and hold ALARM TIME SET A or

B for at least 2 seconds.

“WAKE UP” appears and the hour flashes in

the display.

2 Press ALARM TIME SET + or –

repeatedly until the desired hour appears.

To cycle the hour rapidly, press and hold

ALARM TIME SET + or –.

3 Press ALARM TIME SET A or B.

The minute flashes.

4 Repeat step 2 to set the minute.

5 Press ALARM TIME SET A or B.

The days of the week flash.

6 Repeat step 2 to set the days of the week.

You can select the days from the following

three options:

Every day: SUN MON TUE WED THU FRI

SAT

Week day: MON TUE WED THU FRI

Week end: SUN SAT

7 Press ALARM TIME SET A or B.

The alarm mode setting is entered.

8 Press ALARM TIME SET + or –

repeatedly until the desired alarm mode

flashes.

You can choose one of 3 settings: “ ,”

“RADIO” or “BUZZER.” Set the alarm mode

as follows:

–

: see “ Setting the “WALKMAN” /

Sony Ericsson Phone alarm.”

– RADIO: see “ Setting the radio alarm.”

– BUZZER: see “ Setting the buzzer alarm.”

 Setting the “WALKMAN” / Sony

Ericsson Phone alarm

1 Perform steps 1 to 8 in “To set the

alarm.”

2 Press SELECT on the Docking Tray to

select the “WALKMAN” or Sony

Ericsson Phone connector.

3 Press ALARM TIME SET A or B to select

“

” alarm mode.

“VOL” flashes in the display.

4 Press ALARM TIME SET + or – to adjust

the volume.

5 Press ALARM TIME SET A or B.

The setting is entered.

6 If “A” or “B” does not appear in the

display, press ALARM TIME SET A or B

again.

The “WALKMAN” / Sony Ericsson Phone will

sound at the set time. With the alarm mode

set to “WALKMAN” / Sony Ericsson Phone,

when the alarm time met, if “WALKMAN” or

Sony Ericsson Phone is not attached to the

unit, the alarm sound will be the buzzer.

Notes



Select music library on your “WALKMAN” /

Sony Ericsson Phone with it connected to this

unit when you set the alarm mode to

“WALKMAN” / Sony Ericsson Phone.



Power on the “WALKMAN” / Sony Ericsson

Phone before connecting to this unit.

 Setting the radio alarm

1 Perform steps 1 to 8 in “To set the

alarm.”

2 Press ALARM TIME SET A or B to select

“RADIO” alarm mode.

“VOL” appears in the display.

3 Press ALARM TIME SET + or – to adjust

the volume.

4 Press ALARM TIME SET A or B.

Band (“FM” or “AM”) or “– –” flashes.

“– –” is the last station received.

5 Press ALARM TIME SET + or – to select

the desired band or “– –.”

If you select “– –,” jump to step 8.

6 Press ALARM TIME SET A or B.

The preset number flashes.

7 Press ALARM TIME SET + or – to select

the desired preset number.

The setting is entered.

8 If “A” or “B” does not appear in the

display, press ALARM TIME SET A or B

again.

The radio will turn on at the set time.

 Setting the buzzer alarm

1 Perform steps 1 to 8 in “To set the

alarm.”

2 Press ALARM TIME SET A or B to select

“BUZZER” alarm mode.

The setting is entered.

3 If “A” or “B” does not appear in the

display, press ALARM TIME SET A or B

again.

The buzzer will sound at the set time.

Note

The volume cannot be set for the buzzer alarm.

Setting the clock for

the first time

This unit is preset to the current date and time at

the factory, and is powered by the backup battery.

All you need to do the first time is just plug it in

and select your time zone.

1 Plug in the unit.

The current CET (Central European Time)

appears in the display.

2 Press and hold BRIGHTNESS/TIME

ZONE for at least 2 seconds.

Area number “1” flashes in the display.

3 Press ALARM TIME SET + or –

repeatedly to select the number as

follows:

Area number Time zone

1 (default

setting)

Central European Time/

Central European

Summer Time

Eastern European Time/

Eastern European

Summer Time

0 Western European Time/

Western European

Summer Time

4 Press BRIGHTNESS/TIME ZONE to set.

Note

Though the clock is correctly set at the factory,

discrepancies may arise during transport or

storage. If necessary, set the clock to the correct

time by referring to “Setting the clock manually.”

When Daylight Saving Time

(summer time) begins

This model automatically adjusts for Daylight

Saving Time (summer time).

“

” is displayed from the beginning of Daylight

Saving Time (summer time) and disappears at the

end of Daylight Saving Time (summer time)

automatically.

Automatic DST/Summer Time adjustment is

based on GMT (Greenwich Mean Time).

Area number 0:



Daylight Saving Time (summer time) begins at:

1:00 AM on the final Sunday of March.



Standard time begins at: 2:00 AM on the final

Sunday of October.

Area number 1:



Daylight Saving Time (summer time) begins at:

2:00 AM on the final Sunday of March.



Standard time begins at: 3:00 AM on the final

Sunday of October.

Area number 2:



Daylight Saving Time (summer time) begins at:

3:00 AM on the final Sunday of March.



Standard time begins at: 4:00 AM on the final

Sunday of October.

To cancel Automatic DST/Summer Time

adjustment during the Daylight Saving

Time (summer time) period

The Automatic DST/Summer Time adjustment

can be canceled.

Press and hold CLOCK and SNOOZE/DATE/

SLEEP OFF at the same time at least 2 seconds

while the clock is displayed.

“

” and “OFF” appear in the display to show that

Automatic DST/Summer Time adjustment has

been canceled. The display returns to the clock.

Notes



Changes to Automatic DST/Summer Time

adjustment by the unit (see above) are subject

to circumstances and laws in each country/

region. Should this interfere with desired

adjustment, cancel the Automatic DST/Summer

Time adjustment and set the DST display

manually as necessary. Customers living in a

country/region that does not use Daylight

Saving Time (summer time) must cancel

Automatic DST/Summer Time adjustment

before using the unit.



To activate Automatic DST/Summer Time

adjustment again, press and hold CLOCK and

SNOOZE/DATE/SLEEP OFF at the same time

at least 2 seconds.

“

” and “On” appear in the display to show

that Automatic DST/Summer Time adjustment

has been activated. The display returns to the

clock.

Setting the clock manually

1 Plug in the unit.

2 Press and hold CLOCK for at least

2 seconds.

The year starts to flash in the display.

3 Press ALARM TIME SET + or –

repeatedly to set the year.

4 Press CLOCK.

5 Repeat steps 3 and 4 to set the month,

day, hour and minute, and then press

CLOCK.

The seconds start incrementing from zero.

Notes



If you do not press any button for about

1 minute while setting the clock, the clock

setting will be canceled.



A c

alendar is installed in this unit. When the

date is set, the day of the week is automatically

displayed.

SUN = Sunday, MON = Monday,

TUE = Tuesday, WED = Wednesday,

THU = Thursday, FRI = Friday, SAT = Saturday

To display the year and date

Press SNOOZE/DATE/SLEEP OFF once for the

date, and press it again for the year.

After a while, the display will change back to the

current time automatically.

Setting the brightness

of the display

Three levels of brightness are available by pressing

BRIGHTNESS/TIME ZONE.

Operating the radio

–Manual tuning

1 Press RADIO BAND to turn on the radio

and select the AM or FM band.

2 Press TUNING + or – (TUNE + or – on

the remote) to tune in to a desired

frequency.

3 Adjust the volume using VOLUME + or

– (VOL + or – on the remote).

To confirm an alarm time setting

Press ALARM TIME SET + or –. The setting will

be displayed for about 4 seconds.

To change an alarm setting

Press and hold ALARM TIME SET + for at least

2 seconds to move the alarm time forwards. Press

and hold ALARM TIME SET – for at least

2 seconds to move the alarm time back.

When you release the button, the changed time

will be displayed for about 2 seconds. To change

the alarm time again, press ALARM TIME SET +

or – within these 2 seconds, otherwise the setting

change will be fixed as displayed.

To doze for a few more minutes

Press SNOOZE/DATE/SLEEP OFF.

The sound turns off but will automatically come

on again after about 10 minutes.

You can change the snooze time by pressing

SNOOZE/DATE/SLEEP OFF repeatedly within

4 seconds.

The maximum length of the snooze time is

60 minutes.

To stop the snooze timer, press OFF/ALARM

RESET (OFF on the remote).

To stop the alarm

Press OFF/ALARM RESET (OFF on the remote)

to turn off the alarm.

The alarm will sound again at the same time the

next day.

To deactivate the alarm

Press ALARM TIME SET A or B to turn off the

alarm A or B indicator from the display.

To activate the alarm

Press ALARM TIME SET A or B to turn on the

alarm A or B indicator in the display.

Notes



If the same alarm time is set for both alarm A

and B, alarm A takes priority.



If there is no operation while the alarm is

occurring, the alarm will stop after about

minutes.

Note on the alarm in the event of a power

interruption

In the event of a power interruption, the alarm

will work until the battery is totally discharged.

However, certain functions will be affected as

follows:



The backlight will not light up.



If the alarm mode is set to “WALKMAN” /

Sony Ericsson Phone or radio, it will change to

buzzer automatically.



If a power interruption occurs while the alarm

is sounding, the alarm will stop.



If OFF/ALARM RESET is not pressed, the alarm

will sound for about 5 minutes.



If “

” appears in the display, the alarm will not

sound in the event of a power interruption.

Replace the battery if “

” appears.



The snooze function will not work.



During a power interruption, each alarm will

sound at the set time only once.

Setting the sleep timer

You can fall asleep to music, etc., using the built-

in sleep timer that turns off the unit automatically

after a preset duration.

1 Press SLEEP while the unit is turned on.

“SLEEP” appears and the sleep time flashes in

the display.

2 Press SLEEP to set the sleep timer

duration.

Each time you press SLEEP, the duration (in

minutes) changes as follows:

90 60 30 15

OFF

The display returns to clock mode for about

4 seconds after you have finished the duration

setting and released SLEEP, and then the sleep

timer starts.

The unit will play for the duration you set, and

then shut off.

To turn off the unit before the preset

time

Press SNOOZE/DATE/SLEEP OFF or OFF/

ALARM RESET (OFF on the remote).

To change the sleep timer setting

You can press SLEEP repeatedly to select the

desired sleep timer setting even after the sleep

timer has been activated.

To deactivate the sleep timer

Press SLEEP repeatedly to set the sleep timer to

“OFF” in step 2.

Connecting external

equipment

To listen to sound

1 Connect the AUDIO IN jack of the unit

to the line out jack or headphone jack of

the external equipment using the audio

connecting cable (supplied).

Audio connecting cable

(supplied)

To external

equipment

2 Press AUDIO IN to display “AUDIO IN.”

3 Play the equipment connected to the

AUDIO IN jack.

Adjust the volume using VOLUME + or –

(VOL + or – on the remote)

To return to the radio

Press RADIO BAND.

The frequency is shown in the display.

To return to the “WALKMAN” / Sony

Ericsson Phone

Press  (play).

To stop listening

Press OFF/ALARM RESET (OFF on the remote),

and stop playback on the connected unit.

Notes



Refer also to the connected equipment’s manual.



The supplied audio connecting cable may not

be used with some external equipment. In this

case, use a cord suitable for the external

equipment you are using.



When you listen to the radio with external

equipment connected, turn off the connected

equipment to prevent noise. If noise occurs,

even when the equipment is turned off,

disconnect and place the external equipment

away from the unit.

Troubleshooting

Should any problem persist after you have made

the following checks, consult your nearest Sony

dealer.

The clock flashes “0:00” due to a power

interruption.



The battery is low. Replace the battery. Remove

the old battery and install a new one.

The radio, “WALKMAN” / Sony Ericsson

Phone or buzzer alarm does not sound at the

preset alarm time.



Check that alarm “A” or alarm “B” is properly

displayed.

The radio or “WALKMAN” / Sony Ericsson

Phone alarm is activated but no sound comes

on at the preset alarm time.



Check the alarm volume setting.

There is no sound from the “WALKMAN” /

Sony Ericsson Phone.



Make sure the “WALKMAN” or Sony Ericsson

Phone is securely connected.



Select music library on your “WALKMAN” /

Sony Ericsson Phone.

There is no sound from the Sony Ericsson

Phone.



Make sure the Sony Ericsson Phone is listed in

“Compatible Sony Ericsson Phone models”



Power on the Sony Ericsson Phone.



Adjust the volume of the Sony Ericsson Phone.



Set Bluetooth function to off on the Sony

Ericsson Phone.

The “WALKMAN” / Sony Ericsson Phone

cannot be operated with this unit.



Make sure the “WALKMAN” or Sony Ericsson

Phone is securely connected.



Make sure the Sony Ericsson Phone is listed in

“Compatible Sony Ericsson Phone models”

The “WALKMAN” / Sony Ericsson Phone

cannot be charged.



Make sure the “WALKMAN” or Sony Ericsson

Phone is securely connected.

The indicator turns red when a compatible

Sony Ericsson Phone (listed in “Compatible

Sony Ericsson Phone models”

) is set

in the unit.



Make sure the Sony Ericsson Phone is on.

The indicator turns on (green), but the Sony

Ericsson Phone does not operate.



Make sure the Sony Ericsson Phone is a

compatible model (listed in “Compatible Sony

Ericsson Phone models”

a or b).

When Daylight Saving Time (summer time)

begins, the clock does not employ the

Daylight Saving Time automatically.



Make sure the clock is set correctly.



Press and hold CLOCK and SNOOZE/DATE/

SLEEP OFF simultaneously for at least

2 seconds to activate the Automatic DST/

Summer Time adjustment function.

Specifications

Time display

24-hour system

“WALKMAN” / Sony Ericsson Phone

section

“WALKMAN”:

DC out: 5V

MAX: 500mA

Sony Ericsson Phone:

DC out: 5V

MAX: 600mA

Radio section

Frequency range

Band Frequency Channel step

FM 87.5 – 108 MHz 0.05 MHz

AM 531 – 1 602 kHz 9 kHz

General

Speaker

Approx. 3.8 cm (1

inches) dia. 8 Ω

Input

AUDIO IN jack (ø 3.5 mm stereo minijack)

Power output

0.8 W (at 10% harmonic distortion)

Power requirements

230 V AC, 50 Hz

For clock back up: 3V DC, CR2032 battery (1)

Dimensions

Approx. 167 × 124.7 × 97.1 mm (w/h/d)

× 4

× 3

inches) including projecting

parts and controls

Mass

Approx. 971 g (2 lb 2.2 oz) including power

supply unit

Supplied accessories

Remote commander (1)

AM loop aerial (1)

Audio connecting cable (1)

Attachment for “WALKMAN” (2)

Design and specifications are subject to change

without notice.

4-155-637-41(1)

The  (play) and VOLUME + buttons have a tactile dot.

The “

” mark in the display indicates that the “WALKMAN” or Sony Ericsson Phone function

is activated.

AC power

cord

FM wire aerial

The  and VOL + buttons have a tactile dot.

4-155-637-41(1)

FM/AM

Радио с часовник

Ръководство за експлоатация

ICF-C8WM

Dream Machine е запазена марка на Sony Corporation

http://www.sony.net/

Отпечатано в Чехия

1 2

Summary of Contents

Page 1 - Радио с часовник

EnglishWARNINGTo reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.To reduce the risk of fire, do not cover

Page 2 - Подобряване

FM кабелна антенаЗахранващ кабелДо бутоните  и VOL + има лека подутина, осезаема при допир.Български езикПРЕДУПРЕЖДЕНИЕ2 Натиснете и задръжте RADIO B