CRX100ECD-R/RW Drive UnitUser’s Guide3-865-162-11(3)
10Example of System SetupTo use the CD-R/RW device, the following components arerequired:• Computer (IBM-PC/AT, HP Vectra, or equivalent)• IDE Host ad
11Setting the JumpersSet the jumpers on the rear of the drive in accordance with theconfiguration of your computer system.The jumpers are preset at th
12Slide the drive into the lower bay.Installing the Drive Unit into the ComputerOpening the Computer1 If your computer has its rear side covered by a
13Connecting the DriveConnect the drive to the computer with the following connectors:• DC INPUT connector• AUDIO OUT connector (if you plan to connec
14Frame ground tabFrame ground cableInstalling the Drive Unit into the Computer Frame groundWhen normally installed, the drive unit is not in contact
15 AUDIO OUT connectorThe pin assignment is as follows: INTERFACE CONNECTOR1 Firmly insert one end of the interface cable into the INTER-FACE CONNEC
16Install the host adapter inone of the expansion slots.Installing the Drive Unit into the ComputerMounting the Host AdapterInstall the host adapter i
17Installing the Software DriverMSCDEX and the device driver for an ordinary CD-ROM drive canbe used when using the CRX100E as a CD-ROM drive.Use the
18Operating the DriveThis section describes how to start the drive and eject a disc.Starting the Drive1 Turn on the power of your computer.2 Press the
19Operating the DriveNote:When the drive is set up in vertical position, use the disc locks toprevent your disc from falling. See “How to Use the Disc
2Owner’s RecordThe model and serial numbers are located on the top of the drive. Record these numbersin the spaces provided below. Refer to them whene
20Operating the DriveEjecting the DiscTo eject the disc, press the eject button on the front panel. The traycomes out automatically.Note:The eject but
21 Operating the DriveHow to Use the Disc LocksThe disc tray has four disc locks that prevent the disc from fallingwhen the drive is set up in vertica
22Operating the DriveWhen the drive’s right side is downTo facilitate disc handling, set the disc locks B, C and D into thelocked position, and leave
23SpecificationsSpecifications GeneralHost interface ATAPI compliantRead FunctionAcceptable discs: CD-ROM mode-1 data discsCD-ROM XA discsCD-Audio di
24SpecificationsOutermost track: 200 min-1 (200 rpm) at CLV = 1.2 m/s (1×)400 min-1 (400 rpm) (2×)800 min-1 (800 rpm) (4×)1600 min-1 (1600 rpm) (8×)50
25SpecificationsVibrationOperating Read: 1.96 m /s2(0.2 G o-p) at 5 Hz to300 Hz (sweep)Write:0.98 m /s2(0.1G o-p) at 5Hzto 300 Hz(sweep)Non-operating
26Specifications ConnectorsPower-in/Interface/ID Jumper Switch/Audio connectorIRISO IMSA-9012B-55Z01-GTRecommended Mating (Female) Connectorsfor POWE
27SpecificationsDiese Ausrüstung erfüllt die Europäischen EMC-Bestimmungen für die Verwendung infolgender / folgenden Umgebung(en):• Wohngegenden• Gew
CRX100ECD-R/RW Drive UnitUser’s Guide©1998 by Sony Corporation Printed in Japan
3This unit uses CD-RW discs with the following mark.This unit uses CD-R discs with the following mark.This unit uses CD-ROM discs with the following m
4Declaration of ConformityTrade Name: SONYModel No.: CRX100EResponsible Party: Sony Electronics Inc.Address: 1 Sony Drive, Park Ridge, NJ. 07656 USATe
5ContentsIntroduction 6Location and Function of Parts and Controls 7Front Panel ...
6IntroductionFeaturesThe CRX100E is an internal CD-R/RW (Compact Disc Recordable/ReWritable) drive unit designed for use with an IBM PC, HP Vectra,or
7Location and Function of Parts and ControlsFront Panel3461 2511111Disc trayAccepts a CD-ROM, CD-R and CD-RW disc on its tray.22222Emergency eject hol
8Rear Panel1 2 3 45 611111F.GND (Frame ground) tabConnect with one of the host computer’s ground cables when thedrive’s frame is not in direct contact
9Precautions Installation• Avoid placing the drive in a location subject to:–high humidity–high temperature–excessive dust–mechanical vibration–direc
Comments to this Manuals