Sony SDX-450V User Manual

Browse online or download User Manual for Cleaning media Sony SDX-450V. Sony SDX-450V User's Manual

  • Download
  • Add to my manuals
  • Print

Summary of Contents

Page 1 - AIT Drive

AIT Drive2-546-777-11(1) 2004 Sony CorporationAIT-1 Turbo TAPE DRIVESDX-450VAIT-E Turbo TAPE DRIVESDX-250VUser’s Guide

Page 2

10Useable CartridgesThe SDX-450V can be used with data cartridges marked with the AIT-ETurbo, AIT-1 Turbo or AIT-1 logo.The SDX-250V can be used with

Page 3 - IMPORTANT SAFEGUARDS

11InstallationSCSI Connection/Setting the SCSI IDSCSI 68pin Connector5 VPower Connector1234GND GND 12 VDisableEnableParityNote := = = CLOSED/JumperDon

Page 4

12Option Switches (DIP Switch)DIP Switch PositionsDefaultONOFF123456781 Drive Mode (OFF)2 Drive Mode (OFF)3 Drive Mode (OFF)4 Drive Mode (OFF)5 Termin

Page 5 - Contents

13DR (Disaster Recovery*) ModeONOFF12345678*In Disaster Recovery Mode, the drive enters the DR Standby Mode 15seconds after you insert a write-protect

Page 6 - Overview

14Cleaning Request ModePeriodic cleaning requests can be enabled by a DIP switch.ONOFF12345678When switch 6 is ON, cleaning requests are enabled. When

Page 7 - Introduction

15Mounting HolesFor 3.5" Standard Height155.0 0.5mm [6.10" 0.02"]90.0 0.3mm [3.54" 0.01"]60.0 0.3mm[2.36" 0

Page 8

16For 5.25" Half Height79.2 0.3mm [3.12" 0.01"]79.2 0.3mm [3.12" 0.01"]47.5 0.3mm[1.87" 0.01"]7.0mm[0.2

Page 9 - Precautions

17Reconfiguring from 5.25" Model to 3.5" ModelYou can reconfigure the 5.25" model to the 3.5" model yourself.1 Remove the 2 screws

Page 10 - SCSI Termination

18Orientation10°10°10°10°10°10°10°10°

Page 11 - Installation

19Attaching and Removing the DustCoverAttaching the Dust Cover1 Align the dust cover’s hinge clips (one on each side) with thepins of the drive bezel.

Page 12 - Option Switches (DIP Switch)

2This document contains proprietaryinformation which is protected bycopyright.All rights reserved. No part of thisdocument may be photocopied,reproduc

Page 13 - 12345678

202 Press down at an angle on each side in turn until you hearthe hinge clips click into place.CautionDo not press the dust cover in horizontally from

Page 14

21Removing the Dust Cover1 Open the dust cover.2 Holding the dust cover at both corners, carefully raise thedust cover.The dust cover hinge clips and

Page 15 - Mounting Holes

22OperationLocation of 3 LEDsThere are three LED indications (TAPE MOTION LED, CLEANINGREQUEST LED, REPLACE TAPE LED) and an EJECT button on thefront

Page 16 - For 5.25" Half Height

23Drive OperationLoading a CartridgeNoteWhile setting the data cartridge, do not turn off the host computer. Thismay cause a malfunction or damage dat

Page 17 - 2 Take the side rail off

24Unloading a CartridgeThe cartridge can be removed from the SDX-450V and SDX-250V eitherin response to a SCSI Unload Command, or by pressing the EJEC

Page 18 - Orientation

25Using a Cleaning CartridgeTo keep the AIT drive in top condition, clean the head as needed using ahead cleaning cartridge with the AIT logo. When th

Page 19 - Attaching the Dust Cover

26Emergency Tape Removal Procedure1 Remove the drive from the chassis or enclosure to allowaccess to the bottom of the drive.2 Remove the drive’s top

Page 20 - 3 Close the dust cover

27CautionStop rotating the motor shaft immediately, when the guide B gets to thearea below the line C-C (This line is defined by 2 circular tape guide

Page 21 - 1 Open the dust cover

28Interface ImplementationSupported SCSI MessagesAbort Message Parity ErrorBus Device Reset Message RejectCommand Complete No OperationDisconnect Rest

Page 22 - Operation

29MassSDX-450V SDX-250V 3.5" 740 g (26.1 oz.) 740 g (26.1 oz.) 5.25" 970 g (34.2 oz.) 970 g (34.2 oz.)SpecificationsProduct Specificatio

Page 23 - 2 Open the dust cover

3IMPORTANT SAFEGUARDSFor your protection, please read thesesafety instructions completely beforeoperating the appliance, and keep thismanual for futur

Page 24 - Write-protecting a Cartridge

30Power RequirementsSDX-450VVoltage Max RippleCurrentTypical Maximum5 V +/– 5 % 100 mVp-p 1.1 A 1.4 A12 V +/– 10 % 150 mVp-p 0.4 A 1.2 ASDX-250VVoltag

Page 25 - Storage Precautions

31Sony ContactsFor further information, please contact:Sony Electronics Inc., Tape Storage Solutions (USA)URL: http://www.storagebysony.comSony Corpor

Page 26 - Reel motor

32Sony Corporation of Hong Kong Ltd. Shanghai Rep. Office44F., HSBC Tower, 101 Yin Cheng East Road, Pudong, New Area,Shanghai, P.R.C. Postcode 200120T

Page 30 - Air-cooling Requirement

Printed on 100% recycled paper.Printed in JapanSony Corporation

Page 31 - Sony Contacts

4INSTALLATIONWater and Moisture – Do not usepower-line operated units near water -for example, near a bathtub,washbowl, kitchen sink, or laundrytub,

Page 32

5ContentsOverview ...6Introduction ...

Page 33

6OverviewThe Sony SDX-450V and SDX-250V drives are high capacity data storagedevices using Advanced Intelligent tape (AIT) technology. The SDX-450Vand

Page 34

7IntroductionAbout AIT DrivesThe SDX-450V is an internal AIT drive unit that uses data cartridgesconforming to the AIT-1 Turbo format. The SDX-250V is

Page 35

8The AIT Drive Unit SDX-250V has the following features:• Supports reading and writing to data cartridges conforming to the AIT-ETurbo format.• The th

Page 36 - Printed on 100% rec

9PrecautionsInstallationAvoid placing the drive in a location subject to:– high humidity– high temperature– mechanical shock and vibration– direct sun

Comments to this Manuals

No comments