Sony ICF-M88B User Manual download pdf

Installing the unit on the

bicycle

Install the Wheel Magnet

1 Remove the screw of the wheel magnet and open.

2 Attach the magnet between two spokes of the front wheel with the

head of the screw facing inward, and tighten the screw.

Install the Mount

1 Choose the appropriate rubber pads according to the diameter of the

handlebar and attach them.

Use one or two rubber pads depending on the diameter of the handlebar. You

can attach the Mount clamps without the rubber pads if not required.

The Mount clamps are adjustable. You can adjust the width of the clamps to

fit your handlebar.

2 Install the Mount on the rubber pads and secure with the 4 screws.

3 Wind the sensor cord around the break cable.

Note

Be sure to allow enough cord slack to ensure full movement and unhindered

operation of the handlebar, and not to wind it too loosely as this may interfere

with the unit’s operation.

4 Temporarily attach the Sensor to a fork using the attached

Double-sided tape.

• When attaching, align the center of the sensor and that of the magnet (triangle

mark).

• Ensure a clearance not exceeding 4mm (except Sensor and Magnet touching)

between the Sensor and the Wheel magnet (when aligned).

• Attach the unit on the Mount, and then check the reaction of the sensor by

revolving the wheel (See fig. “Install the unit”).

English

Features

• FM/AM PLL(phase locked loop) synthesized radio with built in cycle-computer

•New ergonomic design

• Splash-resistant for all-weather use

• 15 station memory presets (10FM/5AM)

• Easy Jog lever operation

• Easy to see backlit LCD

• Easy to install mounting kit included

• FM SENS DX(Distance)/LOCAL switch

Installing the Batteries

1 Slide OPEN to open the battery compartment lid and install two

size R6 (AA) batteries (not supplied) with correct polarity.

When the batteries are first installed, “AM 12:00” flashes in the display.

Once the current time is set, the flashing stops. (See “Setting the Clock.”)

*Packing inside of the lid is used to ensure splash-resistance for the battery

compartment. Therefore, make sure to close the battery compartment lid

securely.

2 Close the lid.

Battery Life (Approx. hours) (JEITA*)

When using FM AM

Sony alkaline size LR6 (AA) 66 84

Sony size R6 (AA) 23 31

* Measured by JEITA (Japan Electronics and Information Technology Industries

Association) standards.

The actual battery life may vary depending on circumstances of use.

Replace the batteries

When the batteries become weak, the sound may become weak or distorted, and

“E” will flash in the display. After that, when the batteries are used up, "E"

will light up and clock time display appears. And then the cycle-computer

function will be stopped so that any button functions will not work. The Radio

function will be also turned off if it is on. If this happens, replace the batteries

with new ones.

After the batteries are replaced, press RADIO POWER, RESET, or install the

unit on the Mount. (“E” turn off in the display.)

Note on replacing the batteries

Do not take more than 5 minutes to replace the batteries, otherwise, the clock

setting will be initialized. Should that happen, reset the functions.

Notes on batteries

• Do not charge the dry batteries.

• Do not carry the dry batteries together with coins or other metallic objects. It

can generate heat if the positive and negative terminals of the batteries

accidentally come into contact with metallic objects.

•When you are not going to use the unit for a long time, remove the batteries to

avoid damage from battery leakage and corrosion.

• Do not use different types of batteries at the same time.

•When you replace the batteries, replace all with new ones.

Operating Instructions

Mode d’emploi (au verso)

3-267-406-22(1)

FM/AM PLL Synthesized Radio

ICF-M88B

Printed on 100% recycled paper using

VOC (Volatile Organic Compound)-free

vegetable oil based ink.

Insert the # side of the battery first.

Size R6 (AA) × 2

Packing*

After determining the position of the Sensor, secure it with the zip

tie to front fork and cut any surplus. Install the Sensor cord with zip

ties such that it does not become tangled with the wheel.

Note

Be careful that the position of the Sensor does not shift when tightening the zip

tie.

Install the unit

Install the unit on the Mount, sliding from the front until it clicks into position.

RADIO POWER

Remove the unit

Pull the unit forward while pushing down the lever.

RADIO POWER

LIG

Note

Ensure that the contact points between the Mount and the unit are clean for

proper operation.

Caution

For safe and proper use of the cycle-computer, check whether the Mount, the

sensor and its cord and the wheel magnet are set properly before riding.

4mm

Zip tie

Wheel magnet

Sensor

Wheel magnet

Thin rubber pads

Mount with wheel sensor

Mount clamp

DIO

MPH

FREEZE

PRESET

MHz

MPH

kHz

km/h inch

km/h

mile

CLOCK ODO DIST RT AVG MAX

RADIO POWER LIGHT ENTER/SELECT TUNE MODE BAND/SET

VOL*

FM antennaFM SENS

DX/LOCAL

Jog lever

* There is a tactile dot beside VOL to show the direction to turn up

the volume.

FM SEN

Precautions

• Operate the unit only on 3 V DC with two size R6 (AA) batteries.

•Avoid exposure to temperature extremes, direct sunlight, moisture, sand, dust or

mechanical shock. Never leave in a car parked under the sun.

•Avoid continuous exposure to direct sunlight or extremely high temperatures to

prevent possible damage to the display. The display will function normally

again in normal operating temperature.

• Display switching may become slower in cold climates.

• Should any solid object or liquid fall into the unit, remove the batteries and

have the unit checked by a qualified personnel before operating it any further.

•To clean the casing, use a soft cloth dampened with a mild detergent solution.

• Since a strong magnet is used for the speaker. Keep away personal credit cards

using magnetic cording or spring-wound watches from the unit to prevent

possible damage from the magnet.

Cautions on Splash-resistance

This unit is designed so that it can be used with slight exposure to rain, snow and

other forms of moisture, but there are several points on which caution should be

observed.

• Do not allow it to come into contact with large amounts of water.

• Do not immerse it in water.

• If water should get on it or if it should fall into water, take it out immediately

and wipe it off with a dry cloth. To prevent the battery from corroding, wipe out

the interior of the battery compartment as follows:

–Open or close the battery compartment with dry hands in a place without

exposure to any water.

–Wipe off the battery and the inside of the battery compartment. Give special

attention to the contacts so that no water remains on them.

Notes on the cycle-computer radio

•The user must obey all traffic laws when using the device.

•To check whether the local laws allow the use of the device.

• In order to prevent dangerous condition, do not operate the device when

running the bicycle.

• In order to prevent theft, take your device with you at all times.

• In order to prevent dangerous condition, install the sensor cord properly so that

it will not get tangle by the tire.

If you have any questions or problems concerning your unit, please consult your

nearest Sony dealer.

The preset stations may be initialized, if a maintenance service is performed.

Please keep a copy of your settings in case you want to preset them again.

Specifications

Time display: 12-hour system

Frequency range:

Band Range Channel step

FM 87.5 - 108 MHz 0.1 MHz

AM 530 - 1 710 kHz 10 kHz

531 - 1 710 kHz 9 kHz

Speaker: Approx. 50 mm (2 inches) dia, 8Ω

Power output: 80 mW (at 10% harmonic distortion)

Power requirements: 3V DC, two size R6 (AA) batteries

Dimensions :

Approx. 166.8 × 70 × 95 mm (w/h/d) (6

⁄

× 2

⁄

× 3

⁄

inches) incl.

projecting parts and control.

Mass: Approx. 281.4 g (9.93 oz) incl. batteries / excl. accessories

Supplied accessories:

Mount with wheel sensor (1), Thick/Thin rubber pads (2 each),

Wheel magnet (1), Zip ties (5), Double-sided tape (1), Screws (2)

Design and specifications are subject to change without notice.

Thick rubber pads

Screw

Mount

Sensor

cord

For the initial setting

(with the radio off)

The cycle-computer needs initial set up before using.

If the wheel size you set into the cycle-computer is not suitable for using actual

wheel size, it is not possible to measure speed and distance correctly.

1 Press and hold BAND/SET for a few seconds to select “mile” or

“km”.

“mile” flashes in the display.

Each press of the ENTER/SELECT toggles between “mile” and “km”.

The unit of speed is “MPH” for miles, and “km/h” for kilometers.

Select and show the desirred unit.

2 Press BAND/SET to set a wheel size.

The wheel size flashes.

Press ENTER/SELECT repeatedly to select your wheel size (inches). Each

press changes the display as follows.

26 27 28 12 14

1618202224

Note

The “mm” values shown on the display are approximate. Adjust the accurate size

of the wheel using Jog lever + or - after measuring diameter of your wheel.

It is recommend to set the wheel size in “mm” because the cycle-computer

calculates in “mm”. If you set the wheel size in “mm”, the range is from 300 to

750 mm.

Push and hold Jog lever to change the value rapidly.

3 Press BAND/SET.

“ODO” appears in the display, and the last digit of the total distance

(odometer) flashes.

If you do not change the odometer, jump to step 4.

To change the total distance

You can change the default setting of the total distance (odometer) using Jog

lever + or - (to increase or decrease) and ENTER/SELECT (to select

another digit).

4 Press BAND/SET again.

The initial setting is completed.

Tips

• When you choose the “mile”, the range is from 0.0 to 99 999.9 miles.

•When you choose the “km”, the range is from 0.0 to 159 999.9 kilometers. And

the maximum digit range is from 0 to 15.

Notes

• If you do not make any selections, for within about 65 seconds, or do press

TUNE/MODE button during the initial setting mode, the setting mode will be

canceled and the unit returns to the previous mode.

• If you press the LIGHT button for within about 65 seconds during the initial

setting mode, the setting mode will be extended.

• If you cancel during initial setting mode, the value of the unit, wheel size and

total distance entered will be erased. The unit will revert to the previous setting.

•The cycle-computer will not activate during the initial setting mode.

• If you press RADIO POWER to turn on the unit during the initial setting

mode, the mode is canceled and the radio will activate.

• If you change the unit in the initial setting mode, the values showed in the total

distance (odometer) setting mode will be automatically converted into the new

setting unit. However, when you convert the unit from miles to kilometers, any

value over 159 999.9km is shown as 159 999.9km.

Displaying data

While cycling, current speed is always displayed and updated every second.

The highest speed that can be displayed is 124.2 MPH (199.9 km/h) and remains

displayed beyond that speed. Below 2.5 MPH (4.0 km/h), 0.0 is displayed.

Displaying the odometer

Press MODE/FREEZE repeatedly until “ODO” appears.

The current total distance is displayed.

Note

If 99 999.9 miles (160 934.3 km) is exceeded, the odometer returns to zero.

Displaying trip distance

Press MODE/FREEZE repeatedly until “DIST” appears.

At the point you want to start calculating the distance, perform the zero reset

operation.

For details on how to perform the zero reset operation, refer to “Performing the

zero reset.”

Note

If 9 999.9 miles (16 093.3 km) is exceeded, the trip distance returns to zero.

Displaying riding time

Press MODE/FREEZE repeatedly until “RT” appears.

The “Hour: Minute: Second” is indicated in the display.

At the point you want to start calculating riding time, perform the zero reset

operation. For details on how to perform the zero reset operation, refer to

“Performing the zero reset.”

Riding time is updated every second.

When one wheel revolution takes over a second, riding time is updated when the

magnet passes the sensor.

If the interval at which the magnet passes the sensor is more than 1 minute, the

calculation is canceled.

Note

If the displayed “99:59:59” is exceeded, riding time returns to zero.

Displaying average speed

Press MODE/FREEZE repeatedly until “AVG” appears.

Average speed is calculated according to trip distance and riding time.

Displaying maximum speed

Press MODE/FREEZE repeatedly until “MAX” appears.

The maximum speed recorded to date is displayed.

Note

If either trip distance or riding time returns to zero, trip distance, riding time and

average speed simultaneously return to zero.

Performing the zero reset

The zero reset operation of trip distance, riding time and average speed are

performed simultaneously and cannot reset individually.

1 Press MODE/FREEZE to display either “DIST,” “RT” or

“AVG.”

2 Press and hold RESET for a few seconds.

“DIST,” “RT” and “AVG” flash.

3 Press RESET again.

The zero reset operation is completed, and “DIST,” “RT” and “AVG” are set

to zero.

You can reset maximum speed only. Select “MAX” in step 1, followed by step 2

and 3.

Setting Freeze mode

You can deactivate odometer calculation, trip distance, riding time, average time,

and maximum speed (except for current speed) with the Freeze mode.

1 Press and hold MODE/FREEZE for a few seconds.

“FREEZE” lights up, and the cycle-computer enters Freeze mode.

To cancel Freeze mode, press and hold MODE/FREEZE for a few seconds.

(“FREEZE” is no longer displayed.)

Standby mode

When your bicycle is stopped with the radio off, and no button is pressed for

more than 10 minutes, the cycle-computer enters Standby mode, and only the

current time is displayed.

To cancel Standby mode

When the unit is attached to the Mount

At the point where you start and the magnet passes the sensor, or you press any

active button, Standby mode is canceled. (The display returns to the previous one

before entering Standby mode.)

When the unit is not attached to the Mount

When you attach the unit to the Mount or press any active button, Standby mode

is canceled.

Note

If the cycle-computer enters Standby mode with Freeze mode activated, Freeze

mode is not canceled.

Using the Backlight

Press LIGHT.

The backlight will light for 10 seconds. If any buttons are pressed

while the backlight is on, the backlight will turn off 10 seconds after

pressing the button.

Setting the Clock

The clock time display of this unit is a 12-hour system.

When the batteries are first installed, “AM 12:00” flashes and “CLOCK” turns on

in the display.

1 Press RADIO POWER to turn off the power.

2 Press MODE/FREEZE repeatedly until “CLOCK” appears.

3 Hold down ENTER/SELECT for more than 2 seconds until

“AM 12” starts flashing.

4 Push the Jog lever towards + or – to adjust the hour, then press

ENTER/SELECT.

The beep sounds and the minute setting starts to flash.

If you hold down the Jog lever towards + or –, the digit changes rapidly.

Midnight is indicated as “AM 12:00” and Noon is indicated by “PM 12:00.”

5 Repeat step 4 above to adjust the minutes.

“:” starts flashing and the clock starts operating.

To set the current time exactly to the second, adjust the minute setting and

then press ENTER/SELECT to synchronize it with a time signal (such as

the telephone time signal).

Note

If you do not push the Jog lever towards + or –, or ENTER/SELECT within

about 65 seconds, the clock setting mode will be canceled.

Changing AM Channel Step

The AM channel step differs depending on area. The channel step of this unit is

factory-set to 10 kHz. Change the settings as shown below to be able to listen to

the radio.

Area Channel step

North and South American countries 10 kHz

Other countries/regions 9 kHz

Note

When the AM channel step is changed, only the preset stations on the AM band

will be initialized.

1 Press RADIO POWER to turn off the power.

2 While holding down ENTER/SELECT, keep pressing RADIO

POWER for more than 5 seconds.

Two short beeps sound, and the AM channel step will change and “9” kHz

(or “10” kHz) will light up for about 2 seconds in the display.

If you proceed to step 2 again, the channel step changes again.

Operating the Radio

— Manual Tuning

1 Press RADIO POWER to turn on the power.

2 If “PRESET” is displayed, press TUNE MODE so that

“PRESET” disappears.

Pressing TUNE MODE will switch over between manual tuning mode and

preset tuning mode.

3 Press BAND/SET to select the band.

Each press changes the band.

4 Push the Jog lever towards + or – to select the desired frequency.

If you hold down the Jog lever towards + or –, the frequency changes

rapidly.

When the frequency matches the broadcast frequency, the broadcast will be

received.

5 Adjust the volume using VOL.

To turn off the radio, press RADIO POWER.

Improving Radio Reception

FM: Set FM SENS to LOCAL if interference is

prevalent when radio wave intensity is dramatically

stronger.

Under normal conditions, set to DX.

Presetting your Favorite

Stations

— Preset Tuning

You can preset up to 5 AM stations, and 10 FM stations. You can also delete a

preset station, whether factory-set or preset yourself.

Presetting a Station

1 Follow steps 1 to 5 in “Operating the Radio” and manually tune in

to the station you wish to preset.

2 Hold down ENTER/SELECT until the preset number flashes.

A preset number with no station will flash.

When all preset numbers have assigned stations (factory-set), "1" flashes and

"PRESET" appears.

3 Push the Jog lever towards + or – to select the number you wish to

preset, then press ENTER/SELECT.

If a preset number you select with the Jog lever has an assigned preset

station, "PRESET" appears; if no station is assigned, only the number flashes.

When you press ENTER/SELECT, the selected preset number lights up in

the display.

Example: Preset number 2, FM 90.0 MHz

To preset another station, repeat the above steps.

To change a preset station, preset a new station. The previous station will be

canceled.

Note

If you do not perform a preset operation for about 65 seconds, presetting mode

will be canceled.

Tuning in to a Preset Station

1 Press RADIO POWER to turn on the power.

2 Press BAND/SET to select the band.

3 Press TUNE/MODE so that “PRESET” and preset number

appear.

4 Push the Jog lever towards + or – to select the desired preset

number.

5 Adjust the volume using VOL.

To turn off the radio, press RADIO POWER.

Note

If you hold down TUNE/MODE for more than 2 seconds, the unit enters the

preset station deleting mode. Press TUNE/MODE again to return to the previous

mode.

Deleting a Preset Station

1 Follow steps 1 and 3 in “Tuning in to a Preset Station”.

2 Push the Jog lever towards + or – to select the preset number to be

deleted.

3 Hold down TUNE/MODE for more than 2 seconds until

“PRESET”, “ ” and the preset number flash.

preset number to be deleted

4 While the letters and the preset number are flashing, press

ENTER/SELECT.

The station set to the preset number just before the deleted station will be

displayed.

To delete other stations, repeat steps 2 to 4.

If all the preset stations are deleted, “PRESET -” appears in the display.

To cancel deleting, press TUNE/MODE while “PRESET”, “

” and the

preset number are flashing.

Operating the Radio on the

Mount

When the current speed is displayed (for example, after having installed the unit

on the Mount), pressing a button or the Jog lever (to perform a radio operation)

only displays the station frequency and/or current preset number. From this

display, press the BAND/SET, TUNE/MODE or Jog lever + or - to perform the

desired radio operation.

Holding down Jog lever + or -, ENTER/SELECT or TUNE/MODE while the

current speed is displayed

Jog lever + or - : Pushing the Jog lever displays the current frequency.

Pushing and holding the Jog lever changes the frequency or

preset number.

ENTER/SELECT : Pressing this button displays the current frequency.

Pressing and holding selects the Station-presetting mode.

TUNE/MODE : Pressing this button displays the current frequency.

Pressing and holding selects preset station deleting mode in

preset tuning mode. In manual tuning mode, holding down

has no effect.

Notes

• If you perform a radio operation once in the current speed display and do not

operate the radio again within 5 seconds, the display automatically returns to

the current speed indication.

•When the radio is turned off, the current speed display appears. When the radio

is turned on, the current frequency is displayed. If you do not perform any

operation within 5 seconds, the display returns to the current speed.

• While presetting mode or deleting mode, the current speed display will not

appear. After completing or canceling the presetting/deleting mode, the current

speed display appears after 5 seconds.

1 2

26 27 28 12 14 1
1618202224 1

Summary of Contents

Page 1 - 1618202224

Installing the unit on thebicycleInstall the Wheel Magnet1 Remove the screw of the wheel magnet and open.2 Attach the magnet between two spokes of the

Page 2

Installation de l’appareil surla bicycletteInstallation de l’aimant de roue1 Retirez la vis de l’aimant de roue et ouvrez l’aimant.2 Fixez l’aimant en

Sony ICF-M88B User Manual

Browse online or download User Manual for Bicycle accessories Sony ICF-M88B. Sony ICF-M88B Operating Instructions

Summary of Contents

More documents for Bicycle accessories Sony ICF-M88B

Comments to this Manuals